Question is ⇒ If φsh is flux of shunt magnet, φse is flux of series magnet, ish is eddy current due to φse, the torque in an induction wattmeter is proportional to, Options are ⇒ (A) φse ise + φsh ish, (B) φsh ise - φse ish, (C) φsh ish - φse ise, (D) φsh ish + φse ise, (E) , Leave your comments or Download question paper.

Question is ⇒ If φsh is flux of shunt magnet, φse is flux of series magnet, ish is eddy current due to φse, the torque in an induction wattmeter is proportional to, Options are ⇒ (A) φse ise + φsh ish, (B) φsh ise - φse ish, (C) φsh ish - φse ise, (D) φsh ish + φse ise, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If φ_sh is flux of shunt magnet, φ_se is flux of series magnet, i_sh is eddy current due to φ_se, the torque in an induction wattmeter is proportional to
A.	φ_se i_se + φ_sh i_sh [Wrong Answer]
B.	φ_sh i_se - φ_se i_sh [Correct Answer]
C.	φ_sh i_sh - φ_se i_se [Wrong Answer]
D.	φ_sh i_sh + φ_se i_se [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The resonance frequency is
ω_r = a
ω_r = b
ω_r = k
ω_r = ba

⇒ While forming Routh's array, the situation of a row of zeros indicates that the system
has symmetrically located roots
is not sensitive to variations in gain
is stable
is unstable

⇒ Poynting vector is associated with
flux in magnetic field
power flow in electrostatic field
current in electrostatic field
charge in electrostatic field

⇒ To increase Q factor of a coil, the wire should be
long
thin
thick
long and thin

⇒ The PCM signal shown below uses amplitude level of +1 volt and -1 volt to represent binary symbol 0 and 1 respectively. Each code word consists of 4 bits. The sampled version of analog signal from which this PCM signal is derived
EB596
CD231
DA495
25B6A

⇒ The correct hierarchy of operations for the operators & &, = = , = , * is
& & , = = , = , *
* , = = , & & , =
* , & & , = = , =
= , & & , = = , *

⇒ If A = 3 + j1, A⁴
100 ∠18.43°
100 ∠73.72°
10 ∠18.43°
10 ∠73.72°

⇒ The stray capacitance between the last stage and the first stage of an oscillator may cause
unwanted low frequency oscillations
unwanted high frequency oscillations
unwanted oscillations at low and high frequencies
large feedback

⇒ Figure shows an RC circuit. The magnitude plot V₂/V_{1will rise exponentially to R₂/(R₁ + R₂) as ω → ∞
will rise linearly to R₂/(R₁ + R₂) as ω → ∞
will decrease to zero as ω → ∞
will rise 1 at ω = 0 and then decrease as ω → ∞}

⇒ A 1 μF capacitor is connected to 12 V battery. The energy stored in the capacitor is
12 x 10^-6 J
24 x 10^-6 J
48 x 10^-6 J
72 x 10^-6 J

⇒ A system is said to be static system, when present output depend upon
present I/P
presrent and past
present and future
past and future

⇒ Which of these has a magnetic brake?
Thermocouple ammeter
Energy meter
Dynamometer wattmeter
Frequency meter

⇒

Match the following:

	List I (Transducer)		List II (Operation)
A.	Bourden tube	1.	Fluid flow to resistance change
B.	Hot wire ammeter	2.	Velocity to pressure
C.	Hydrometer	3.	Pressure to displacement
D.	Pitot tube	4.	Specific gravity to displacement

A-1, B-3, C-2, D-4
A-3, B-1, C-2, D-4
A-3, B-1, C-4, D-2
A-4, B-2, C-3, D-1

⇒ In a two stage cascade amplifier, each stage has a gain of 10 dB and noise figure of 10 dB. The overall noise factor is
10
1.09
1
10.9

⇒ Which of the following are true for relative dielectric constant?

It is dimensionless.
It is equal to 1 for vacuum.
It is equal to 1 for all substances.

1 and 2 only
2 and 3 only
1 and 3 only
1, 2 and 3

⇒ If the functions w, x, y, z are as foll
w = z x = z
w = z, x = y
w = y
w = y = z

⇒ The voltage gains of an amplifier without feedback and with negative feedback respectively are 100 and 20. The percentage of negative feedback (β) would be
0.4
0.05
0.2
0.8

⇒ How is an N-channel junction Field Effect Transistor operated as an amplifier?
With a forward bias gate source junction
With a reverse bias gate-source junction
With a open gate source junction
With a shorted gate source junction

⇒ A series RLC circuit is supplied from a variable frequency source. The resonant frequency is ω₀. The voltage across L is maximum at a frequency
equal to ω₀
slightly less than ω₀
slightly more than ω₀
none of the above

⇒

Assertion (A): A TRIAC is a bidirectional SCR.

Reason (R): A TRIAC is a four layers 3 terminal device and can conduct in both directions.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ A thyristor has a maximum allowable junction temperature of 120°C and the ambient temperature is 40°C. If thermal resistance is 1.6° C/W, the maximum allowable internal power dissipation is
20 W
50 W
92 W
128 W

⇒

Match the following:

	List I (I/P - O/P relation)		List II (Property of the system)
A.	y(n) = x(n)	1.	Nonlinear, non-causal
B.	y(n) = x(n²)	2.	Linear, non casual
C.	y(n) = x²(-n)	3.	Linear causal
D.	y(n) = x²(n)	4.	Nonlinear causal

A-1, B-4, C-3, D-2
A-3, B-2, C-1, D-4
A-1, B-2, C-3, D-4
A-3, B-4, C-1, D-2

⇒ In a 50 cm TV tube, a path difference of 2 km between direct wave and interfering wave would mean a displacement between main image and ghost image equal to
0.3 cm
3 cm
6 cm
9 cm

⇒ A constant k low pass filter has f_c = 500 Hz. At f = 1000 Hz, the attenuation is
zero
infinity
may be zero or infinity
more than zero but less than infinity

⇒ EPROM can be
UVPROM
EEPROM
both UVPROM and EEPROM
none of the above

⇒ If A = 4∠7°, A² is
16∠14°
16∠49°
16∠7°
16∠3.5

⇒ In the circuit of the given figure, V_{05 V
3.1 V
2.5 V
0}

⇒ In common base connection, the output characteristics of a bipolar junction transistor is drawn between
I_C and V_CB
I_C and V_CE
I_E and V_CB
I_E and V_CE

⇒ For the circuit of the given figure, the output equatio
Y = ABCD
Y = AB + CD
Y = A + BCD
Y = ABC + D

⇒ Consider the following statements.

Etching
Exposure to UV radiation
Stripping
Developing

After a wafer has been coated with photo resist the correct sequence of these steps in photolithography is
2, 4, 3, 1
2, 4, 1, 3
4, 2, 1, 3
3, 2, 3, 1