Question is ⇒ In a 3 phase full converter feeding a highly inductive load, the average load current is 150 A. The peak current through thyristor is, Options are ⇒ (A) 150 A, (B) 75 A, (C) 50 A, (D) 300 A, (E) , Leave your comments or Download question paper.

Question is ⇒ In a 3 phase full converter feeding a highly inductive load, the average load current is 150 A. The peak current through thyristor is, Options are ⇒ (A) 150 A, (B) 75 A, (C) 50 A, (D) 300 A, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a 3 phase full converter feeding a highly inductive load, the average load current is 150 A. The peak current through thyristor is
A.	150 A [Correct Answer]
B.	75 A [Wrong Answer]
C.	50 A [Wrong Answer]
D.	300 A [Wrong Answer]
View Answer 2 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a metal, the drift velocity of electrons in the presence of a electric field E is
proportional to E
proportional to E
inversely proportional to E
proportional to E²

⇒ Aperture circuit produces __________ in sample hold circuit.
the total sampling time
delay between the instance at which hold command is initiated and the instance at which O/P starts tracking I/P
the time taken by O/P to settle within the specified 1% error band, that of the I/P
time required by holding capacitor to reach upto the level close to input

⇒ The diffusion current is proportional to
applied electric field
concentration gradient of charge carrier
square of the electric field
cube of the applied electric field

⇒ Waveform shown in figure is that
FM
PCM
AM-DSB
AM-SSB

⇒ In equally tampered musical scale, an octave is divided into
12 intervals
10 intervals
7 intervals
5 intervals

⇒ In Gunn diode electrons are transferred from
Ridge guide is essentially a form of capacitively loaded guide
low to high mobility energy bands
valley to domain formation
domain to valley formation

⇒ What is typical bandwidths of a 2-wire telephone line?
300 Hz to 3.4 kHz
20 Hz to 4 kHz
dc to 4 kHz
20 Hz to 20 kHz

⇒ With I_s disconnected I = - 1, when I_s = b is connected, the value of I will be
0.0833333333333333
-1 A
0.0416666666666667
0.125

⇒ A TEM wave incident obliquely on a dielectric boundary with ε_r1 = 2 and ε_r2 = 1, the angle of incidence for total reflection is
30°
60°
45°
90°

⇒ A remote control of TV uses a 10 bit word. The maximum number of total commands it can transmit is
64
256
512
1024

⇒ In a single phase full wave ac regulator using two thyristors only, the gate circuits of the two thyristors
must be isolated
may or may not be isolated
should be preferably, isolated
should not be isolated

⇒ For free space propagation
γ = a + jβ
γ = jβ
γ = a
a = β = 0

⇒ Commercial ECL gates use two ground lines and one negative supply to
reduce power consumption
increase fan out
reduce loading effect
eliminate the effect of power line glitches on the biasing circuit

⇒ An ungrounded antenna near the ground
is horizontally polarized
acts as an antenna array
acts as a single antenna of twice the height
is not likely to need an earth mat

⇒ An audio signal is to be transmitted digitally. Which is the system best suited for good fidelity?
8 bit PCM
13 bit PCM
32 bit PCM
PCM system with non-uniform quantizer

⇒ (sI - A)^-1 is equal to
adj (sI - A)/det (sI - A)
det (sI - A)/adj(sI - A )
[adj (sI - A)] [det(sI - A)]
none of the above

⇒ At room temperature the barrier potential in a silicon diode is
0.1 V
0.3 V
0.7 V
1 V

⇒ In a CE amplifier the input impedance is equal to the ratio of
ac base voltage to ac base current
ac base voltage to ac emitter current
ac emitter voltage to ac collector current
ac collector voltage to ac collector current

⇒ In a ripple counter,
whenever a flip flop sets to 1, the next higher FF toggles
whenever a flip flop sets to 0, the next higher FF remains unchanged
whenever a flip flop sets to 1, the next higher FF faces race condition
whenever a flip flop sets to 0, the next higher FF faces race condition

⇒ When avalanche breakdown occurs covalent bonds are not affected.
TRUE
FALSE

⇒ In a specimen of ferromagnetic material, as the flux density is increased from zero to 2.5 T, µ_r will
increase
decrease
first decrease then increase
first increase then decrease

⇒ CC circuit is suitable for impedance matching.
TRUE
FALSE

⇒ Giga watt is equal to
10¹² W
10⁹ W
10⁶ W
10³ W

⇒ For an P-channel enhancement type MOSFET determine the drain current if K = 0.278 x 10^-3A/V², V_GS = -4V, V_T = -2V, Voltage equivalent at 27°C = 26 mV.
10 mA
1.11 mA
0.751 mA
46.98 mA

⇒

Assertion (A): Industrial robots improve productivity.

Reason (R): Robots can handle monotonous and complex jobs without error in operation.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ A source of angular frequency 1 rad sec has a source impedance consisting of 1 Ω resistance in series with 1 H inductance. The load that will obtained the maximum power transfer is
1 Ω resistance
1 Ω resistance in parallel with 1 H inductance
1 Ω resistance in series with 1 F capacitor
1 Ω resistance in parallel with 1 F capacitor

⇒ In which one of the following types of analog to digital converts the conversion time is practically independent of the amplitude of the analog signal?
The dual slope integrating type
Successive approximation type
Counter ramp type
Tracking type

⇒ For AB + A C + BC = AB + A C the dual form is
(A + B) (A + C)(B + C) = (A + B)(A + C)
(A + B ) (A + C)(B + C) = (A + B)(A + C)
(A + B) (A + C) (B + C) = (A + B) (A + C)
none of the above

⇒ A single phase step up cycloconverter changes 50 Hz to 100 Hz. Then one half wave of input will give rise to
one half wave of output
one full wave of output
two full waves of output
either (b) or (c)

⇒ A 3 phase semiconverter when supplying a certain load has a rectification efficiency of 0.6 and transformer utilisation factor of 0.35. When a 3 phase full converter is supplying the same load
rectification efficiency will be more than 0.6 and TUF will be more than 0.35
rectification efficiency will be more than 0.6 but TUF will be less than 0.35
rectification efficiency will be less than 0.6 and TUF will be less than 0.35
rectification efficiency will be less than 0.6 but TUF will be more than 0.35