Question is ⇒ Consider 49 cascaded amplifiers having individual rise time as 2 n sec. 3 n sec. ... 50 n sec. The input waveform rise time is 1 n sec. Then the output signal rise time is given time by (Assume output signal rise time is measured within 10 percent range of the final output signal.), Options are ⇒ (A) 39 - 28 μsec, (B) 2.28 μsec, (C) 0.228 μsec, (D) 39.28 μsec, (E) , Leave your comments or Download question paper.

Question is ⇒ Consider 49 cascaded amplifiers having individual rise time as 2 n sec. 3 n sec. ... 50 n sec. The input waveform rise time is 1 n sec. Then the output signal rise time is given time by (Assume output signal rise time is measured within 10 percent range of the final output signal.), Options are ⇒ (A) 39 - 28 μsec, (B) 2.28 μsec, (C) 0.228 μsec, (D) 39.28 μsec, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Consider 49 cascaded amplifiers having individual rise time as 2 n sec. 3 n sec. ... 50 n sec. The input waveform rise time is 1 n sec. Then the output signal rise time is given time by (Assume output signal rise time is measured within 10 percent range of the final output signal.)
A.	39 - 28 μsec [Wrong Answer]
B.	2.28 μsec [Wrong Answer]
C.	0.228 μsec [Correct Answer]
D.	39.28 μsec [Wrong Answer]
View Answer 3 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Two identical silicon diodes D₁ and D₂ are connected back to back shown in figure. The reverse saturation current I_s of each diode is 10^-8 amps and the breakdown voltage V_Br is 50 v. Evaluate the voltages V_D1 and V_D2 dropped across the diodes D₁ and D₂ assuming KT/q to be 25
4.983 V, 0.017 V
- 4.98 V, - 0.017 V
0.17 V, 4.983 V
- 0.017 V, - 4.98 V

⇒ A constant k high pass p section has a characteristic impedance of 300 Ω at f = ∞ . At f = f_c, the characteristic impedance will be
zero
∞
300 Ω
more than 300 Ω

⇒ Which of the following is not an application software?
MS Word
DBMS
Worksheet
Lisp

⇒ In FSK no synchronous carrier is needed at the receiver
TRUE
FALSE
depend on distance
none

⇒ The poles and zeros of a positive real functions are real or occur in conjugate pair.
TRUE
FALSE

⇒ If too large current passes through the diode
all electrons will leave
all holes will freeze
excessive heat may damage the diode
diode will emit light

⇒ A broadcast radio transmitter radiates 5 kW when the modulation percentage is 60. How much of this is carrier power?
6.66 kW
5 kW
4.9 kW
4.23 kW

⇒ The trigonometric Fourier series for the waveform f(t) shown below con
only cosine terms and zero value for the dc component
only cosine terms and a positive value for the dc component
only cosine terms and a negative value for the dc component
only sine terms and a negative for the dc component

⇒ In a D latch
a high D sets the latch and low D resets it
a low D sets the latch and high D resets it
race can occur
none of the above

⇒ For a series RLC circuit bandwidth is ω₂ - ω₁ = R/2L.
TRUE
FALSE

⇒ CMRR of an op-amp is about 0.1.
TRUE
FALSE

⇒ Consider the following statements associated with two port networks.

Z₁₂ = Z₂₁
Y₁₂ = Y₂₁
h₁₂ = h₂₁
AD - BC = 1

Which one of the statement given above are correct?
1, 2, 3
2, 3, 4
1, 3, 4
1, 2, 4

⇒ The spectral component of noise associated with k^th frequency is given, in the limit as Δf → 0 by n_k(t) written as n_k(t) = C_k cos (2pk Δft + θ_{k1, 2 only
1, 3 only
1, 2, 3
2, 3 only}

⇒

Match the following:

	List I (Transducer)		List II (Operation)
A.	Bourden tube	1.	Fluid flow to resistance change
B.	Hot wire ammeter	2.	Velocity to pressure
C.	Hydrometer	3.	Pressure to displacement
D.	Pitot tube	4.	Specific gravity to displacement

A-1, B-3, C-2, D-4
A-3, B-1, C-2, D-4
A-3, B-1, C-4, D-2
A-4, B-2, C-3, D-1

⇒ The unit of loudness is
phon
sone
decibel
mel

⇒ For a nonlinear resistance
v-i plot is not a straight line
resistance increases as current increases
resistance decreases as current increases
current decreases as voltage increases

⇒ Schmitt trigger is used for wave shaping.
TRUE
FALSE

⇒ In figure, the voltmeter is ideal. The transformer has two identical windings with perfect coupling. The reading of voltmete
440 V
220 V
110 V
zero

⇒ A capacitor can be represented by a capacitance C in parallel with a resistance R. For a good capacitor, the resistance R should be
very high
high
very low
low

⇒ TTL logic is preferred to DRL logic because
greater fan-out is possible
greater logic levels are possible
greater fan-in is possible
less power consumption is achieve

⇒ The input 3-dB frequency is :
100 Hz
148 Hz
100 kHz
None

⇒ A carrier signal at frequency 100 MHz is frequency modulated with modulation index 2 by a signal at 2 kHz. At what frequencies are the sidebands produced?
102 MHz and 98 Mhz
100 MHz + 2 kHz, 100 MHz - 2 kHz
100 MHz ± Δf_d where f_d is frequency deviation
100 MHz ± 3n kHz, where n is 1, 2, ... S integer

⇒ Selectivity varies with receiving frequency, frequency is raised.
Somewhat better when the receiving frequency is raised
Somewhat better at intermediate frequency
Somewhat worse when the receiving frequency is lowered
Somewhat worse when the receiving frequency is raised

⇒ An LED is
an ohmic device
a display device
a voltage regulated device
all of the above

⇒

Assertion (A): The ac load line is different from dc load line

Reason (R): The ac load resistance seen by collector and emitter is different from dc load resistance

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ Henry is equivalent to
Volts/Ampere
Weber/Volt
Weber/Ampere
Weber/Ampere²

⇒ When a particular mode is excited in a waveguide, these appears an extra electric components in the direction of propagation. The resulting mode is
Transverse electric
Transverse magnetic
Longitudinal
Transverse Electromagnetic

⇒ The network shown in the figure represen
band pass filter
low pass filter
high pass filter
band stop filter

⇒ Waveguides are generally used above
20 MHz
100 MHz
200 MHz
1000 MHz

⇒ For the shaded area in Venn diagram of the given figure, the Boolean expressio
AB + BC + CA
ABC + A B C
ABC + A B C
ABC+AB