Question is ⇒ Pirani gauge is used to measure, Options are ⇒ (A) very low pressure, (B) high pressure, (C) pressure in the range of 1 atmosphere, (D) fluid flow, (E) , Leave your comments or Download question paper.

Question is ⇒ Pirani gauge is used to measure, Options are ⇒ (A) very low pressure, (B) high pressure, (C) pressure in the range of 1 atmosphere, (D) fluid flow, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Pirani gauge is used to measure
A.	very low pressure [Correct Answer]
B.	high pressure [Wrong Answer]
C.	pressure in the range of 1 atmosphere [Wrong Answer]
D.	fluid flow [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ An amplifier has a large ac input signal. The clipping occurs on both the peaks. The output voltage will be nearly a
sine wave
square wave
triangular wave
(a) or (c)

⇒ The speeds used in recording audio programs in house hold recorders are
38 cm/s and 9.5 cm/s
38 cm/s and 19 cm/s
9.5 cm/s and 4.75 cm/s
38 cm/s and 4.75 cm/s

⇒ Dish antennas are
loop
helical
parabolic
conical

⇒ The unit of loudness is
phon
sone
decibel
mel

⇒ Adder is a combinational logic circuit.
TRUE
FALSE

⇒ Figure shows an RC potentiometer to measure ac voltage. It is desired that V₀/V_i should be independent of frequency. The value of C should
10 μF
11 μF
0.1 μF
0.09 μF

⇒ The transconductance curve of a JFET is
a straight line
parabolic
hyperbolic
inverted V-type

⇒ The quantum numbers associated with electron motion are designed as
a, b, c
h, k, l
n, m, l
h, n, l

⇒ Even at room temperature, an intrinsic semiconductor has some holes. These holes are due to
electron
doping
thermal energy
free electrons

⇒ It is required that a strain gauge has gauge factor of 100. The proper strain gauge is
constantan strain gauge
nichrome strain gauge
semiconductor strain gauge
alloy strain gauge

⇒ Which one of the following gain equations is correct for a MOSFET common-source amplif
A_V = g_m/(1 - R_D)
A_V = g_m/R_D
A_V = g_m/(1 + R_D)
A_V = R_D/g_m

⇒ A Darlington pair is used for
low distortion
high frequency range
high power gain
high current gain

⇒ An enhancement mode MOSFET is on when the gate voltage is
zero
positive
high
more threshold value

⇒ The voltage and current distributions on a grounded λ/4 dipole (Marconi antenna) are similar to those of a half wave dipole in space.
TRUE
FALSE

⇒ Microprocessors find applications in
pocket calculators
scientific instruments
medical equipments
all of the above

⇒ Examine the circuit of figure and the following statem
1, 2, 3
1, 2
1 only
2 and 3

⇒

Match the following:

	List I (Functional headings of instruction set of 8085)		List II (Functions performed)
A.	Branch group	1.	Compares, rotates etc.
B.	Logic group	2.	Moves, loads, stores etc.
C.	Data transfer group	3.	Initiates conditional or unconditional jumps, calls etc.

A-1, B-2, C-3
A-2, B-3, C-1
A-3, B-1, C-2
A-1, B-3, C-2

⇒ As the number SWG increases, area of cross-section decreases.
TRUE
FALSE

⇒

Match the following:

	List I (μP)		List II (Number of bits in register)
A.	8085	1.	32 bit
B.	8086	2.	16 bit
C.	68000	3.	8/16 bit

A-1, B-2, C-3
A-2, B-3, C-1
A-3, B-2, C-1
A-3, B-1, C-2

⇒ In a synchro transmitter
input is angular position of rotor shaft and output is stator voltages
input is stator voltages and output is angular position of shaft input is rotor voltage and output is angular position of rotor shaft
input is rotor voltage and output is angular position of rotor shaft
input is angular position of rotor shaft and output is rotor voltage

⇒ Which of the following is used to generate PDM?
Free running multi-vibrator
Monostable multi-vibrator
JK flip-flop
Schmitt trigger

⇒

Assertion (A): An electronic tuner uses varactor diode

Reason (R): The capacitance of a varactor diode depends on the magnitude of reverse bias.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Least expensive logic
RTL
DTL
TTL
ECL

⇒ The source of which of the following noise is different from that of the remaining?
Solar noise
Cosmic noise
Galactic noise
Atmospheric noise

⇒ In AM receiver the oscillator frequency is
always equal to signal frequency
always equal to 455 kHz
always higher than signal frequency
always lower than signal frequency

⇒ A (0.75 - j50) ohm load is connected to a coaxial transmission line of Z₀ = 75 ohms at a frequency of 10 GHz Which of the following will be the best method of matching?
Connecting an inductance at the end
Connecting a short circuited stub at the load
Connecting a capacitance at some distance from the load
Connecting a short circuited stub at some specified distance from the load

⇒ A long specimen of P type semiconductor material
is + vely charged
is electrically neutral
has an electric field directed along its length
acts as a dipole

⇒ A 12 bit ADC is employed to convert an analog voltage of zero to 10 volts. The resolution of the ADC is
2.44 mV
24.4 mV
83.3 mV
1.2 V

⇒ In Bode method of stability analysis, the error curve is not symmetric about corner frequency.
TRUE
FALSE

⇒ A 300 V voltmeter has an accuracy of ± 2% of full scale deflection. When the reading is 222 V, the actual voltage
lies between 217.56 and 226.44 V
lies between 217.4 and 226.6 V
lies between 216 and 228 V
is exact 222 V