Question is ⇒ In 8085 microprocessor, the interrupt enable flip-flop is reset by, Options are ⇒ (A) DI instruction only, (B) system RESET only, (C) interrupt acknowledgment only, (D) all of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ In 8085 microprocessor, the interrupt enable flip-flop is reset by, Options are ⇒ (A) DI instruction only, (B) system RESET only, (C) interrupt acknowledgment only, (D) all of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In 8085 microprocessor, the interrupt enable flip-flop is reset by
A.	DI instruction only [Wrong Answer]
B.	system RESET only [Wrong Answer]
C.	interrupt acknowledgment only [Wrong Answer]
D.	all of the above [Correct Answer]
View Answer 3 -3 Explanation:- Answer : D Discuss it below : Haithem Murshed Said on 2021-06-14 15:40:58 Computer Graphics Write a Python code to draw the attched drawing using Tkinter Library. !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ When a voltage is applied to a semiconductor crystal then the free electrons will flow.
towards positive terminal
towards negative terminal
either towards positive terminal or negative terminal
towards positive terminal for 1 μs and towards negative terminal for next 1 μs

⇒ For the shaded area in Venn diagram of the given figure, the Boolean expressio
AB + BC + CA
ABC + A B C
ABC + A B C
ABC+AB

⇒ A quarter wave line short circuited at load end behaves as
an inductance
an inductance and capacitance in series
a capacitance
an inductance and capacitance in parallel

⇒ Which of the following is same in AM and FM receivers?
Demodulator
AGC
IF amplifier
All of the above

⇒ If f₁ and f₂ and half-power frequency and f₀ be resonant frequency, the selectivity of R-L-C series circuit is given by
(f₂ - f₁)/2f₀
(f₂ - f₁)/f₀
(f₂ - f₀)/(f₁ - f₀)
(f₂ - f₁)/(f₁ - f₀)

⇒ A plot of modulation index vs carrier amplitude yields a
horizontal line
vertical line
parabola
hyperbola

⇒ The simplest method of suppression of unwanted side band in AM is
filter method
phase shift method
third method
both (a) and (b)

⇒ The charges between a hollow and solid metal spheres reside
through out in both
on outer surface in hollow and through out in solid
on the outer surface in both
none of the above

⇒

Assertion (A): Microprocessor 8085 has 16 address bus lines and 8 data bus lines.

Reason (R): Address bus in 8085 is unidirectional.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ In a bipolar transistor, the emitter base junction has
forward bias
reverse bias
zero bias
zero or reverse bias

⇒ From an n channel JFET for V_DS constant and if V_GS is made more negative, pinch off would occur at
higher value of drain current
saturation value of drain current
zero drain current
gate current equal to drain current

⇒ The dependent current source shown in given fig
delivers 80W
absorbs 80W
deliver 40W
absorbs 40W

⇒ If A = 3 + j1 and B = 4 + j3, A - B =
8.062 ∠29.7°
10 ∠45°
2.236 ∠243.43°
6.72 ∠243.43°

⇒ When two 4 bit parallel adders are cascaded we get
4 bit parallel adder
8 bit parallel adder
16 bit parallel adder
none of the above

⇒ Consider the following instruments

Tangent galvanometer
Rayleigh current balance
Household energy meter
Hot wire ammeter

Out of above absolute instruments are
1, 2 and 3
1, 2 and 4
1 and 2
2, 3 and 4

⇒ In a backward wave oscillator the wave travelling along the line winds itself back and forth
TRUE
FALSE

⇒ Some ceramic materials become superconducting
below liquid helium temperature
between liquid helium and liquid nitrogen temperature
above liquid nitrogen but below room temperature
at room temperature

⇒ In a tape recorder the erase head is
engaged during playback but disengaged during recording
engaged both during recording and playback
disengaged both during recording and playback
engaged during recording but disengaged during playback

⇒ As compared to an ordinary semiconductor diode, a Schottky diode
has lower cut in voltage
has higher cut in voltage
lower reverse saturation current
both (b) and (c)

⇒

Assertion (A): A large negative feedback is deliberately introduced in an amplifier to make its gain independent of variation in parameters of active device.

Reason (R): A large negative value of feedback results in a high value of return difference compared to unity which makes the feedback gain inversely proportional to the feedback factor.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ When the gate terminal of MOSFET is positive, it is said to operate in
depletion mode
conduction mode
enhancement mode
none of the above

⇒ In the circuit of figure, the switch is closed at t = 0. At t = 0⁺ the current through
0.166666666666667
2.5 A
3.1 A
0

⇒ S_i transistor of following figure has a = 0.9 and I_CE= 0, V_EE = 5 V and V_CC = 13 V, then R_E will be if I_EQ =
3 kΩ
4 kΩ
5 kΩ
4.3 kΩ

⇒ The Z-inverse of the given Z-transform is _______
unit step
unit ramp
unit impulse
unit parabola

⇒ - 56 is not a valid real constant in Fortran.
TRUE
FALSE

⇒ In figure, transistor β_dc = 100 and LED voltage when it is conducting is 2 V. Then the base current which saturates the transisto
18 mA
1.8 mA
0.18 mA
0.018 mA

⇒

Assertion (A): FET has characteristics very similar to that of pentode.

Reason (R): Both FET and pentode are voltage controlled devices.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒

Match the following:

	List I		List II
A.	bit	1.	10
B.	nat	2.	e
C.	decit	3.	2

A-1, B-2, C-3
A-1, B-3, C-2
A-3, B-2, C-1
A-2, B-3, C-1

⇒ In a single phase full wave regulator feeding an R-L load, the power factor angle of load is θ. The range of control of firing angle a is
0 ≤ a ≤ p
θ ≤ a ≤ p
0 ≤ a ≤ (p - θ)
θ ≤ a ≤ (p + θ)

⇒ In the circuit of figure, the value of r_e is (neglecting v_{be100 Ω
75 Ω
50 Ω
25 Ω}