Question is ⇒ A mod-10 counter can divide the clock frequency by a factor of, Options are ⇒ (A) 10, (B) 20, (C) 210, (D) 102, (E) , Leave your comments or Download question paper.

Question is ⇒ A mod-10 counter can divide the clock frequency by a factor of, Options are ⇒ (A) 10, (B) 20, (C) 210, (D) 102, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A mod-10 counter can divide the clock frequency by a factor of
A.	10 [Correct Answer]
B.	20 [Wrong Answer]
C.	210 [Wrong Answer]
D.	102 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In radar PRF depends on maximum range.
TRUE
FALSE

⇒ A five bit binary adder is used to add 01001 and 00111. The adders from LSB position are numbered as FA₀, FA₁, FA₂ and FA₃. The outputs of FA₂ are
SUM = 0
SUM = 0, CARRY = 1
SUM = 1, CARRY = 0
SUM = 1, CARRY = 1

⇒

Match the following:

	List I		List II
A.	Zener diode	1.	used in seven segment display
B.	Tunnel diode	2.	used in voltage regulator circuits
C.	LED	3.	used is solar energy utilization
D.	Photovoltaic cell	4.	used in digital circuits

A-1, B-3, C-2, D-4
A-2, B-3, C-1, D-4
A-2, B-4, C-1, D-3
A-3, B-2, C-4, D-1

⇒ RECTIFIER : OSCILLATOR ::
Capacitance : Inductance
Series resonance : Parallel resonance
DC : AC
Regulation : Efficiency

⇒ For the circuit, let us assume that R = 1 Ω, L = 10^-3 H, and V(t) = 10 cos (1000t + 30°)V and the differential equation for I(t) is give
7.07 cos (1000t + 15°) A
70.7 cos (1000t - 30°) A
7.07 cos (1000t - 15°) A
7.07 cos (1000t + 15°) A

⇒ For a BJT, under the saturation region.
I_C = βI_B
I_C > βI_B
I_C is independent of other parameter
I_C < βI_B

⇒ The material used in RTD is
linear
aluminium
silver
platinum

⇒ Indicate the false statement: To combat noise
reduce signalling rate
increase transmitted power
use redundancy
increase channel bandwidth

⇒

Assertion (A): Negative feedback reduces the bandwidth of an amplifier

Reason (R): Negative feedback stabilizes the gain of an amplifier

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ A 360 W carrier is simultaneously modulated by two audio wave with modulation percentage of 55 and 65 respectively. Total sideband power radiated will be
500 W
360 W
180 W
130 W

⇒ Ferromagnetic materials
shows spontaneous magnetisation below a certain temperature
have resistivity very high as compared to that of iron
can be used even at microwave frequencies
all of the above

⇒ The residual resistivity of a binary alloy at 0 K is
sum of residual resistivities of component metals
difference of residual resistivities of component metals
product of residual resistivities of component metals
dependent on the concentration of minor component in the alloy

⇒ In a series circuit with X_L constant and R variable the current locus lies in the third quadrant.
TRUE
FALSE

⇒ An excitation is applied to a system at t = T and the response in zero for -∞ < t < T. This system is
non casual
stable
casual
unstable

⇒

Assertion (A): Microprocessor 8085 can address 65536 memory locations.

Reason (R): Microprocessor 8085 has 16 address lines.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ Atomic number of germanium is
24
28
32
36

⇒ The radiation resistance of a rod tubing antenna is
55 Ω to 60 Ω
60 to 100 Ω
0 to 377 Ω
60 to 200 Ω

⇒

Assertion (A): In control system velocity error is not an error in velocity but is an error in position due to a ramp input.

Reason (R): For a type of system velocity error is zero.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ Why npn-transistors are preferred over pnp-transistors?
Leakage current in npn-transistors is less than pnp-transistors
Mobility of majority carrier in npra-transistors is greater than the mobility of majority carrier in pnp-transistors
Bias voltage required in npn is less than in/wp-transistors
Bias voltage required in npn is greater than in pnp-transistors

⇒ A rectangular pulse is passed through an L.P.F. The response is a
triangular
trapezoidal function
sampling
Both (a) and (b)

⇒ The scale of dynamometer wattmeter is non linear.
TRUE
FALSE

⇒ In which condition does BJT behave like a closed switch?
Cut off
Saturation
Forward active
Reverse active

⇒ Status register in the 8156 contains information about
the timer
the ports
both (a) and (b)
none of the above

⇒ While calibrating an ammeter by a dc potentiometer it is necessary to use a standard resistance.
TRUE
FALSE

⇒ Manganin, an alloy of copper and manganese, is used in
Soldering material
Heating elements
Ballast resistors
Standard resistances

⇒ A material which is lightly repelled by a magnetic field is known as
diamagnetic material
non-magnetic material
ferromagnetic material
paramagnetic material

⇒ As compared to bipolar junction transistor, a FET
is less noisy
has better thermal stability
has higher input resistance
all of the above

⇒ The radiation resistance of a λ/16 wire dipole in free space will be nearly
1 Ω
3 Ω
13 Ω
30 Ω

⇒ The real part of complex frequency s corresponds to oscillations.
TRUE
FALSE

⇒ The manufacturing technique used to manufacture strip type transmission line is
photoetching technique
oxidation technique
cladding
epitaxial