Question is ⇒ The dimensions of force are, Options are ⇒ (A) MLT-2, (B) ML-1T-2, (C) MLT-1, (D) ML2T-2, (E) , Leave your comments or Download question paper.

Question is ⇒ The dimensions of force are, Options are ⇒ (A) MLT-2, (B) ML-1T-2, (C) MLT-1, (D) ML2T-2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The dimensions of force are
A.	MLT^-2 [Correct Answer]
B.	ML^-1T^-2 [Wrong Answer]
C.	MLT^-1 [Wrong Answer]
D.	ML²T^-2 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The bandwidth of FM for Commercial Purpose is
88 - 108 MHz
85 - 110 MHz
90 - 110 MHz
infinite Range

⇒ In pulse transmitter the ratio of time on to time off is called
efficiency
duty cycle
base
bandwidth

⇒ The 2732 is 4096 x 8 EPROM. How many address lines does it have?
12
24
50
100

⇒ The ground waves eventually disappear as one moves away from the transmitter because of
tilting
maximum single-hop distance limitation
interference from the sky waves
loss of line-of sight condition

⇒ Accumulator is an 8 bit register and is also known as register B.
TRUE
FALSE

⇒

Assertion (A): Impulse function is an important function in network analysis.

Reason (R): Convolution integral enables us to find the response of a network to an arbitary input in terms of the impulse response.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In using KCL it is necessary that current leaving a node is written as negative.
TRUE
FALSE

⇒ In a multi-processor configuration two coprocessors are connected to host 8086 processor. The instruction sets of the two coprocessors
must be same
may overlap
must be disjoint
must be the same as that of host

⇒ Which of the following statement is correct?
FET and junction transistor both are unipolar
FET and junction transistor both are bipolar
The FET is bipolar, while junction transistor are unipolar
The FET is unipolar, while junction transistor are bipolar

⇒ A circuit is fed by two sources of different frequency and magnitudes 100 ∠0° V and 50 ∠30°V. The current in a particular branch is 10 ∠20° A. If the magnitudes of the sources are changed to 200 ∠0° V and 100 ∠0° V, the current in that branch should be
20 ∠20° A
10 ∠20° A
14.14 ∠20° A
10 ∠- 20° A

⇒ Audio tapes have two tracks each 2.5 mm wide.
TRUE
FALSE

⇒ A photo diode is
forward biased
reverse biased
either forward or reverse biased
unbiased

⇒ In a CE amplifier circuit the load resistance is open circuited. The output voltage will
increase
decrease
become zero
increase or decrease

⇒ A feedback amplifier has forward gains A₁, A₂ and feedback factor β as shown in signal flow graph of the given figure. Because of feedback as shown in signal noise ratio at output
increase
decrease
be unaffected
depend on value of β

⇒ For the network in figure, the correct loop equation for loop
-I₁ + 4I₂ + 11I₃ = 0
I₁ + 4I₂ + 11I₃ = 0
-I₁ - 4I₂ + 11I₃ = 0
I₁ - 4I₂ + 6I₃ = 0

⇒

Assertion (A): Water waves are longitudinal but EM waves are transverse

Reason (R): In an EM wave electric field, magnetic field and propagation are mutually perpendicular.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Long distance short-wave radio broadcasting uses
ground wave
ionospheric wave
direct wave
any of the above

⇒ In a resistor the current is i and the voltage is v. The rate of dissipation of heat at any time t is
vi
vit
vt
vit²

⇒ Whenever a JFET operates above pinch-off voltage
depletion regions become smaller
drain current increase steeply
drain current starts decreasing
drain current remains nearly constant

⇒ Which of the following describe the correct properties of an emitter follower circuit?

It is a voltage series feedback circuit.
It is a current series feedback circuit.
Its voltage gain in less than unity.
Its output impedance is very low.

Select the correct answer from the codes given below:
1, 3 and 4
2, 3 and 4
2 and 3 only
2 and 4 only

⇒

Match the following:

	List I (Bit Pattern)		List II (Register pairs)
A.	00	1.	SP
B.	01	2.	B-C
C.	10	3.	D-E
D.	11	4.	H-L

A-1, B-2, C-3, D-4
A-2, B-3, C-4, D-1
A-2, B-3, C-1, D-4
A-4, B-3, C-2, D-1

⇒ The transistor of following figure in Si diode with a base current of 40 μA and I_CBO = 0, if V_BB = 6V, R_E = 2 kΩ and β = 90, I_BQ = 20 μA then R_{B200 kΩ
265 kΩ
150 kΩ
100 kΩ}

⇒ c(t) and m(t) are used to generate an AM signal. The modulation index of the generated AM signal is 0.5 then the quant
42737
42739
42738
42743

⇒ The circuit of figure give an output which
a frequency modulated signal
an amplitude modulated signal
a phase modulated signal
none of the above

⇒

Assertion (A): Impatt diode is an avalanche diode.

Reason (R): Avalanche breakdown phenomenon occurs when a p-n junction is reverse biased.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ +12 V supply is given to plates a, d, g, and 0 V to other plates and grid of a VF display. The plates which will glow are
a, d, g
b, c, e, f
all
none

⇒ Which of the following oscillator is generally not used at VHF?
Colpitts oscillator
Clapp oscillator
Armstrong oscillator
Ultra Audio oscillator

⇒ In the expression a = 5 * 2 / 3.2 + 4 / 8 - 2 + 5 / 9 which operation will have the first priority in C?
5*2
2 / 3.2
5 * 2 / 3.2
42833

⇒ The condition AD - BC = 1 for two port network implies that the network is a
reciprocal
lumped element network
lossless network
unilateral element network

⇒ A communication channel with AWGN operating at a signal to noise ratio SNR >> 1 and bandwidth B has capacity C₁. If the SNR is doubled keeping B constant, the resulting capacity C₂ is given by
C₂ ≈ 2C₁
C₂ ≈ C₁ + B
C₂ ≈ C₁ + 2B
C₂ ≈ C₁ + 0.3B