Question is ⇒ The physical state in which polymers exist is, Options are ⇒ (A) melts & rubber like state., (B) amorphous glassy state., (C) partially crystalline state., (D) all (a), (b) and (c)., (E) , Leave your comments or Download question paper.

Question is ⇒ The physical state in which polymers exist is, Options are ⇒ (A) melts & rubber like state., (B) amorphous glassy state., (C) partially crystalline state., (D) all (a), (b) and (c)., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The physical state in which polymers exist is
A.	melts & rubber like state. [Wrong Answer]
B.	amorphous glassy state. [Wrong Answer]
C.	partially crystalline state. [Wrong Answer]
D.	all (a), (b) and (c). [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Tyres are made by
injection moulding
extrusion
rotational moulding
compression moulding

⇒ Pick out the wrong statement.
Polystyrene is a thermoplastic polymer.
Protein is a natural polymer.
Neoprene is a natural rubber.
Polythene is a copolymer, while SBR is a homopolymer.

⇒ Fillers such as zinc oxide and carbon black are added to the crude natural rubber before vulcanisation in order to improve its
elasticity
strength
plasticity
weathering characteristics

⇒ A copolymer of vinyl and vinylidine chloride is called
treylene
orlon
saran
dacron

⇒ Softening point of high density polythene is about __________ °C.
85
135
165
205

⇒ Phthalic anhydride is used
in making PVC
as plasticisers
in insecticides manufacture
for making nylon-6

⇒ Hot drink (e.g, tea) cups are usually made of
polystyrene
polythene
polypropylene
PVC

⇒ Which of the following is not a condensation polymer ?
Bakelite
Melamine polymer
Polymethylmethacrylate (PMMA)
None of these

⇒ Silicone resins, which are highly water repellant and has good heat resistance can not be used
as room temperature adhesive.
as grease & lubricant.
hydraulic fluid for heat transfer.
resin for lamination.

⇒ Alkyd resin can not be used for making
plasticiser
paint & varnish
fibres
film forming materials

⇒ Polycaprolactum is
nylon-6
nylon-66
dacron
rayon

⇒ Melt spinning of polymers involves the forcing of polymer melt through spinnerettes (fine holes) into an atmosphere kept at a temperature lower than the melting point of the polymer, which causes the fine diameter polymer melt to harden into filaments. Melt spinning is not used in case of the __________ fibres.
acrylic
polyester
nylon 6:6
polypropylene

⇒ The rate controlling step in the manufacture of silicone rubber is the
polymer termination step.
condensation of siloxane to silicone.
initial hydrolysis of silicone monomer.
none of these.

⇒ Which of the following is a natural polyamide fibre.
Wool
Silk
Cotton
None of these

⇒ Which of the following is the lowest cost plastic commercially available ?
Polythene
Teflon
Bakelite
PVC

⇒ In step growth polymerisation, condensation occurs in a stepwise manner with or without the elimination of smaller molecules. An example of step growth polymerisation product is
terylene
polybutadiene
PVC
polypropylene

⇒ Which of the following is not a natural fibre?
Silk
Viscose rayon
Wool
Cotton

⇒ A copolymer is formed by the combination of two or more monomer molecules
in a chain without the elimination of water.
with the elimination of small amount of water.
of the same monomer by elimination of small molecules of water.
none of these.

⇒ Density of high density polythene is about __________ gm/c.c.
1.18
1.05
0.95
0.99

⇒ __________ is produced by polymerisation of chloroprene.
Thiokol (a polysulphide rubber)
Butyl rubber
Neoprene
Polyurathane rubber

⇒ Paper like thin plastic articles can be produced by
blow moulding
vacuum thermo forming
injection moulding
none of these

⇒ __________ scrap can be recycled & reutilised.
Bakelite
Epoxy resin
Polythene
none of these

⇒ Synthetic polymer produced by using terephthalic acid and ethylene glycol is
terylene
nylon-66
PVC
polyesterene

⇒ Polycaprolactum is nothing but
orlon
nylon 6, 6
nylon 6
saran

⇒ Benzoyl chloride is not used as a catalyst in the manufacture of
polystyrene
polyvinyl acetate
polypropylene
polyvinyl chloride-co-vinylacetate

⇒ Which of the following is not a thermoplastic material ?
Epoxy polymer
PVC
Polystyrene
Polythene

⇒ Which of the following polymers shows the highest anti-tacking properties ?
Melamine formaldehyde resin
Phenolic resin
Epoxy resin
Alkyd resin

⇒ Bristles of tooth brushes are made of
nylon-6
nylon-66
polystyrene
PVC

⇒ Perspex can be used as a substitute of glass. Its monomer is
methyl methacrylate
DMT
butadiene
tetrafluroethylene

⇒ Thermosetting resins/polymers as compared to thermoplastic ones are
soluble in all organic solvents.
more brittle.
formed by addition polymerisation only.
easily reshaped & reused.