Question is ⇒ Nylon-6 as compared to nylon-66 is, Options are ⇒ (A) harder., (B) more abrasion resistant., (C) having higher melting point., (D) none of these., (E) , Leave your comments or Download question paper.

Question is ⇒ Nylon-6 as compared to nylon-66 is, Options are ⇒ (A) harder., (B) more abrasion resistant., (C) having higher melting point., (D) none of these., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Nylon-6 as compared to nylon-66 is
A.	harder. [Wrong Answer]
B.	more abrasion resistant. [Wrong Answer]
C.	having higher melting point. [Wrong Answer]
D.	none of these. [Correct Answer]
View Answer 8 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Benzoyl chloride is not used as a catalyst in the manufacture of
polystyrene
polyvinyl acetate
polypropylene
polyvinyl chloride-co-vinylacetate

⇒ Vinyl flooring is done using __________ sheets.
polypropylene
PVC
polythene
polyvinyl acetate

⇒ Lavatory cisterns are normally made of
expanded polystyrene
saturated polyester
perspex
PVC

⇒ The conversion of caprolactum in the above case is about __________ percent.
25
50
70
90

⇒ Plastic articles are normally produced by __________ moulding.
green sand
injection
shell
dry sand

⇒ Terylene is
same as dacron
a polyester
both(a) & (b)
neither (a) nor (b)

⇒ Which of the following is not a thermoplastic material ?
Epoxy polymer
PVC
Polystyrene
Polythene

⇒ Synthetic polymer produced by using terephthalic acid and ethylene glycol is
terylene
nylon-66
PVC
polyesterene

⇒ Viscosity of a polymer solution or melt
decreases with increase in molecular weight.
decreases with increase in temperature.
increases with increase in temperature.
does not vary with temperature rise.

⇒ In nylon-6, the number 6 represents the total number of
carbon atoms in the ring.
carbon atoms in the linear polymer chain.
nitrogen atoms in the ring.
hydrogen atoms in the ring.

⇒ Polycaprolactum (Nylon - 6) is produced by the condensation polymerisation of caprolactum at 240-280°C in which the conversion of caprolactum is about __________ percent.
50
75
90
99

⇒ Linear polymers are normally
thermosetting.
thermosplastic.
elastometric.
having extremely high softening point.

⇒ Starting material for the production of SBR is
ethyl alcohol
ethylene
both (a) & (b)
neither (a) nor (b)

⇒ __________ tubes are good substitude for human blood vessels onrheart by-pass operation.
PVC
Polythene
Teflon/dacron
Polystyrene

⇒ Terylene is a/an
addition polymer
poly amide
homopolymer
none of these

⇒ Addition polymerisation is not involved in the manufacture of
low density polythene.
poly vinyl chloride.
polystyrene.
polyhexamethylene adipamide.

⇒ Teflon is
phenol formaldehyde
an inorganic polymer
polytetra florouethylene (PTFE)
a monomer

⇒ Nylon-6 is a
polyamide
thermosetting resin
polyester
none of these

⇒ Antioxidants are added to rubber to protect it from the attack of light, heat & atmospheric ozone. Which of the following is an antioxident used in rubber ?
Carbon
Alkylated diphenyl amine
Thiokol
Magnesium

⇒ Polyurathane can not be used to make
automobile cushion
thermal insulation in refrigerator
coating and adhesive
fibre reinforced plastic (FRP)

⇒ Pick out the wrong statement.
Denier is defined as weight in gm of 9000 metres length of a fibre, while tex is defined as weight in gm of 1000 metres length of fibre.
Crimp is a measure of the difference between the length of the straightened and unstraightend fibre.
Dacron fibres, acrylic fibres, viscose rayon fibres & cellulose acetate fibres are all prepared by wet spinning.
Nylon fibres have greater water absorption capacity than polyester fibres.

⇒ Phosphates (e.g., triceresyl, tributyl, tetrabutyl, tripheyl etc.) are added to polymers to act as
hardeners
anti-shrinkage agents
plasticisers
transparency improver

⇒ Amino resins are used in paper treatment to improve its
wet tear and bursting strength.
folding endurance
wet rub resistance
all (a), (b) & (c)

⇒ The physical state in which polymers exist is
melts & rubber like state.
amorphous glassy state.
partially crystalline state.
all (a), (b) and (c).

⇒ Acrylonitrile-butadiene-styrene (ABS) copolymer, which is produced by blending styrene-acrylonitfile copolymer with butadiene based elastomer, is a/an
rigid foam
engineering plastic
thermosetting polymer
spongy rubber

⇒ Polystyrene is a __________ plastic at room temperature.
ductile
brittle
malleable
none of these

⇒ In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament form. Dry spinning is used for __________ fibres.
polythene
PVC
rayon
polyvinyl acetate

⇒ Transistor parts and refrigerator components are normally made of
polystyrene
polyester
high density polythene
polyurathane

⇒ Which of the following is stretched into fibres ?
Saturated polyester
Unsaturated polyester
Isoprene
Bakelite

⇒ __________ is normally used for the manufacture of refrigerator components and transistor parts.
Polyproylene
Polystyrene
Polyester
Polyurathene