Question is ⇒ Liners of bags are usually made of, Options are ⇒ (A) polythene, (B) PVC, (C) polypropylene, (D) polyesters, (E) , Leave your comments or Download question paper.

Question is ⇒ Liners of bags are usually made of, Options are ⇒ (A) polythene, (B) PVC, (C) polypropylene, (D) polyesters, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Liners of bags are usually made of
A.	polythene [Wrong Answer]
B.	PVC [Wrong Answer]
C.	polypropylene [Correct Answer]
D.	polyesters [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Polypropylene compared to polythene is
harder
stronger
lighter
all (a), (b) and (c)

⇒ Which of the following is the most important rubber compounding ingradient which is used to improve wearing qualities of both natural rubber & SBR by imparting toughness ?
Phosphorous
Carbon black
Pine oil
Rosin

⇒ Which of the following is stretched into fibres ?
Saturated polyester
Unsaturated polyester
Isoprene
Bakelite

⇒ Bakelite is
same as polytetra flouro ethylene (PTFE).
an inorganic polymer.
same as thermoset phenol formaldehyde.
not a polymer.

⇒ Synthetic rubber
deforms, if stretched to double of its original dimension.
is brittle at low temperature
is softer at higher temperature.
is highly permeable to air & water and is readily attacked by chemicals & atmospheric gases.

⇒ Pick out the wrong statement.
For the manufacture of styrene, the major raw materials are benzene and ethylene.
One inportant copolymer of styrene is SBR, which is widely used in the manufacture of automobile tyres.
Manufacture of phenol by chloroben-zene-eaustic process involves. The chlorination of benzene, causticisation and hydrolysis.
Phenol manufacture by chlorobenzene-caustic process is competitive even when low cost chlorine is not available.

⇒ The monomer of natural rubber is
DMT
isoprene
2 methyl-1-propene
both (b) and (c)

⇒ Polycondensation reaction of polymerisation
does not produce linear polymers.
produces only thermoplastic material.
produces epoxy polymers.
does not need any catalyst.

⇒ Styrene butadiene rubber (SBR) as compared to natural rubber has
poor tensile strength.
poorer resistance.
greater amount of heat build up heavy loading.
all (a), (b) ana (c).

⇒ Which of the following is a copolymer ?
PVC
Bakelite
Polythene
Teflon

⇒ Cellulose content in bomboo fibre is about __________ percent.
10
20
50
85

⇒ In a cross linked polymer, the monomeric units are linked together to constitute a three dimensional network. Which of the following is a cross-linked polymer ?
Bakelite (phenol formaldehyde)
Polyester
Polythene
Nylon-6

⇒ Which of the following natural bio polymers are formed as a result of polymerisation of amino-acids ?
Starch
Cellulose
Proteins
Nucleic acids

⇒ The monomer for the production of neoprene rubber is
acetylene
chloroprene
isoprene
none of these

⇒ __________ resins are produced by the condensation polymerisation of formaldehyde with urea or melamine.
Epoxy
Amino
Alkyd
Phenolic

⇒ The physical state in which polymers exist is
melts & rubber like state.
amorphous glassy state.
partially crystalline state.
all (a), (b) and (c).

⇒ Which of the following polymers shows the highest anti-tacking properties ?
Melamine formaldehyde resin
Phenolic resin
Epoxy resin
Alkyd resin

⇒ Temperature and gage pressure maintained during the manufacture of hot SBR (styrene butediene rubber) are
50°C and 3 - 4 kg/cm²
50°C and 1 kgf/cm²
250°C and 10 kgf/cm²
250°C and 1 kgf/cm²

⇒ Thiokol is nothing but
polysulphide rubber
polyamide fibre
engineering plastic
exponded polystyrene

⇒ Pick out the correct statement.
Plastics are good conductors of heat and electricity.
All the polymers are highly crystalline in nature
Polymers can be vaporised by heating to a very high temperature.
The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation.

⇒ Which of the following is not a polymer of two monomers ?
Teflon
Bakelite
SBR
None of these

⇒ Thermosetting materials
are cross-linked molecules.
soften on application of heat.
are solvent soluble.
none of these.

⇒ __________ fibres are made of polyamides.
Dacron
Nylon
Rayon
Orion

⇒ Thermosetting polymers as compared to thermoplastic polymers
are formed by addition polymerisation.
have three dimensional structure.
have linear structure.
none of these.

⇒ Vinyl flooring is done using __________ sheets.
polypropylene
PVC
polythene
polyvinyl acetate

⇒ Flexible foam (for mattresses) are usually made of
PVC
silicone rubber
polyurethanes
polyamides

⇒ Polycaprolactum is
nylon-6
nylon-66
dacron
rayon

⇒ __________ tubes are good substitude for human blood vessels onrheart by-pass operation.
PVC
Polythene
Teflon/dacron
Polystyrene

⇒ Melt spinning of polymers involves the forcing of polymer melt through spinnerettes (fine holes) into an atmosphere kept at a temperature lower than the melting point of the polymer, which causes the fine diameter polymer melt to harden into filaments. Melt spinning is not used in case of the __________ fibres.
acrylic
polyester
nylon 6:6
polypropylene

⇒ In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament form. Dry spinning is used for __________ fibres.
polythene
PVC
rayon
polyvinyl acetate