Question is ⇒ The monomer of poly vinyl chloride (PVC) is, Options are ⇒ (A) chloroethene, (B) ethylene dichloride, (C) ethyl chloride, (D) chloroform, (E) , Leave your comments or Download question paper.

Question is ⇒ The monomer of poly vinyl chloride (PVC) is, Options are ⇒ (A) chloroethene, (B) ethylene dichloride, (C) ethyl chloride, (D) chloroform, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The monomer of poly vinyl chloride (PVC) is
A.	chloroethene [Correct Answer]
B.	ethylene dichloride [Wrong Answer]
C.	ethyl chloride [Wrong Answer]
D.	chloroform [Wrong Answer]
View Answer 5 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Dacron is a
condensation polymerisation product of hexamethylene diamine and adipic acid.
condensation polymerisation product of dimethyl terephthalate (DMT) and ethylene glycol.
thermosetting material.
none of these.

⇒ Natural rubber is obtained from latex, which is a colloidal dispersion of rubber in water. Which of the following is used as a coagulant in latex ?
Ammonium alum
Potassium alum
both a & b
neither a nor b

⇒ Polymerisation process in which two or more monomers of chemically different nature take part is called
copolymerisation
addition polymerisation
chain polymerisation
none of these

⇒ Pick out the wrong statement.
For the manufacture of styrene, the major raw materials are benzene and ethylene.
One inportant copolymer of styrene is SBR, which is widely used in the manufacture of automobile tyres.
Manufacture of phenol by chloroben-zene-eaustic process involves. The chlorination of benzene, causticisation and hydrolysis.
Phenol manufacture by chlorobenzene-caustic process is competitive even when low cost chlorine is not available.

⇒ Which of the following is the most important rubber compounding ingradient which is used to improve wearing qualities of both natural rubber & SBR by imparting toughness ?
Phosphorous
Carbon black
Pine oil
Rosin

⇒ The process involved in converting rubber into a thin sheet or coating it on fabric is called
extrusion
mastication
calendering
vulcanisation

⇒ Scouring is a finishing operation during the manufacture of fibre, which aims at __________ of fibres.
improving the stretchability
dyeing/colouring
detergent solution washing
glycol soaking

⇒ A chain growth polymerisation reaction consists of three different types of reaction namely initiation reaction, propagation reaction & termination reaction. Chain growth polymerisation reaction is not involved in the manufacture of
siloxane elastomers.
polyamides.
vinyl polymers.
urea-formaldehyde resins.

⇒ Properties of a polymer is affected by the
chain length.
intermolecular forces.
branching & cross-linking.
all (a), (b).

⇒ Which of the following is not a polyolefin ?
Polystyrene
Polypropylene
Neoprene
None of these

⇒ Vulcanisation of rubber
decreases its tensile strength.
increases its ozone & oxygen reactivity.
increases its oil & solvent resistance.
converts its plasticity into elasticity.

⇒ Polycondensation reaction of polymerisation
does not produce linear polymers.
produces only thermoplastic material.
produces epoxy polymers.
does not need any catalyst.

⇒ Polycaprolactum (Nylon - 6) is produced by the condensation polymerisation of caprolactum at 240-280°C in which the conversion of caprolactum is about __________ percent.
50
75
90
99

⇒ The starting material used for the manufacture of caprolactum is
ethyl benzene
cyclohexane
ethylene glycol
DMT

⇒ Silicone is a/an
monomer
inorganic polymer
thermoplastic material
a natural polymer

⇒ Addition of stabiliser during PVC manufacture is done to
improve its impact strength.
improve its elasticity.
reduce the melt viscosity & glass transition temperature.
prevent its thermal degradation.

⇒ __________ of SBR is adversely affected, if more quantity of styrene is added to butadiene during its co-polymerisation to produce SBR.
Percent elongation
Resilience
Freezing point
Strength

⇒ Thermosplastic materials
do not soften on application of heat.
are heavily branched molecules.
are solvent insoluble.
none of these.

⇒ Bakelite is a/an
addition polymer
elastomer
thermoplastic
none of these

⇒ Pickout the wrong statement.
Polymers made of only one monomer is called homopolymer.
Polymers made of more than one monomer is called copolymer or mixed polymer.
Vulcanised rubber is more elastic than natural rubber.
The intermoleculer forces in ther-mosplastic polymers are intermediate to that of elastomers & fibres.

⇒ The synthetic fibres produced from __________ are known as rayon.
lignin
cellulose
polyamides
ethylene glycol

⇒ The rate controlling step in the manufacture of silicone rubber is the
polymer termination step.
condensation of siloxane to silicone.
initial hydrolysis of silicone monomer.
none of these.

⇒ Nylon-6 as compared to nylon-66 is
harder.
more abrasion resistant.
having higher melting point.
none of these.

⇒ Polymers are
micromolecules
macromolecules
sub-micromolecules
none of these

⇒ Polyvinyl chloride (PVC) is
a thermosetting material.
a condensation polymerisation product.
made by employing emulsion polymerisation.
none of these.

⇒ The repeating units of PTFE are
Cl₂CH-CH₃
F₂ C = CF₂
F₃ C-CF₃
FClC = CF₂

⇒ Tyres are made by
injection moulding
extrusion
rotational moulding
compression moulding

⇒ Orion is
a copolymer.
a condensation polymer.
obtained by polymerising vinyl cyanide.
all (a), (b) and (c).

⇒ Polyvinyl chloride (PVC)
is produced by polycondensation reaction.
uses either emulsion or suspension polymerisation methods.
can be made thermosetting by adding a plasticiser.
softening temperature is 200°C.

⇒ Bristles of tooth brushes are made of
nylon-6
nylon-66
polystyrene
PVC