Question is ⇒ Thermal pyrolysis of ethylene dichloride produces, Options are ⇒ (A) trichlorethylene, (B) vinyl chloride, (C) ethanol amine, (D) ethylene oxide, (E) , Leave your comments or Download question paper.

Question is ⇒ Thermal pyrolysis of ethylene dichloride produces, Options are ⇒ (A) trichlorethylene, (B) vinyl chloride, (C) ethanol amine, (D) ethylene oxide, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Thermal pyrolysis of ethylene dichloride produces
A.	trichlorethylene [Wrong Answer]
B.	vinyl chloride [Correct Answer]
C.	ethanol amine [Wrong Answer]
D.	ethylene oxide [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Contact lenses for eyes are made of perspex, which is nothing but
polymethylmethacrylate
polystyrene
unsaturated polyester
polypropylene

⇒ Styrene butadiene rubber is commercially manufactured by
bulk polymerisation
suspension polymerisation
solution polymerisation
emulsion polymerisation

⇒ Nylon 6 as compared to nylon 6, 6 has lower
abrasion resistance.
thermal stability.
adhesion to rubber.
hardness.

⇒ Vulcanisation of rubber does not increase its
elasticity
plasticity
ductility
none of these

⇒ __________ is not a condensation polymer.
Teflon
Nylon-66
Dacron
Polystyrene

⇒ Polymethyl methacrylate, which is an acrylic resin, is also called
thiokol
plexiglass or lucite
dacron
teflon

⇒ Which of the following is not a condensation polymer ?
Bakelite
Melamine polymer
Polymethylmethacrylate (PMMA)
None of these

⇒ Low pressure Zeigler process for the manufacture of polythene uses a catalyst which is
Ni
V₂O₅
Fe
aluminium triethyl combined with titanium tetrachloride

⇒ __________ polymer is produced by the copolymerisation of vinyl chloride-vinyl acetate.
Fibrous
Leathery
Rubbery
Hard

⇒ Which of the following is not an elastomer ?
Polyisoprene
Neoprene
Nitrile-butadiene
None of these

⇒ Bakelite (phenol-formaldehyde) resin can not be used as
decorative paint.
decorative laminates.
electrical insulation.
glass reinforced plastics.

⇒ Phosphates (e.g., triceresyl, tributyl, tetrabutyl, tripheyl etc.) are added to polymers to act as
hardeners
anti-shrinkage agents
plasticisers
transparency improver

⇒ Perspex can be used as a substitute of glass. Its monomer is
methyl methacrylate
DMT
butadiene
tetrafluroethylene

⇒ A copolymer is formed by the combination of two or more monomer molecules
in a chain without the elimination of water.
with the elimination of small amount of water.
of the same monomer by elimination of small molecules of water.
none of these.

⇒ The synthetic fibres produced from __________ are known as rayon.
lignin
cellulose
polyamides
ethylene glycol

⇒ Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is
7 kgf/cm² and 70 °C.
1000 kgf/cm² and 100°C.
7 kgf/cm² and 700°C.
1 kgf/cm² (gage) and 70°C.

⇒ Polyvinyl chloride (PVC) is
a thermosetting material.
a condensation polymerisation product.
made by employing emulsion polymerisation.
none of these.

⇒ __________ of SBR is adversely affected, if more quantity of styrene is added to butadiene during its co-polymerisation to produce SBR.
Percent elongation
Resilience
Freezing point
Strength

⇒ Which of the following rubbers has the widest service temperature range (-75 to 275°C) ?
Butyl rubber
Silicon rubber
Nitrile rubber
Silicone rubber

⇒ Polymers are classified into four categories namely thermosetting, thermoplastic, elastomer and fibre depending upon their
molecular sizes.
magnitude of intermolecular forces.
resistance to heat.
polymerisation mechanism.

⇒ Crystallisation of polymers is an undesirable property. Crystallisation of celluloid is prevented by adding
glycerol
nitro cellulose
camphor
none of these

⇒ Thermosetting plastic materials
can be repeatedly melted.
is useful for melt casting.
can not be melted after forming.
is useful for spinning.

⇒ Non sulphonated hard bakelites are not used for making
ion-exchange resins
fountain pen barrels
formica table tops
combs

⇒ Which of the following is not a polyolefin ?
Polystyrene
Polypropylene
Neoprene
None of these

⇒ In a cross linked polymer, the monomeric units are linked together to constitute a three dimensional network. Which of the following is a cross-linked polymer ?
Bakelite (phenol formaldehyde)
Polyester
Polythene
Nylon-6

⇒ Which of the following is not the commercial name of polymethylmethacrylate (PMMA) ?
Perspex
Lucite
Plexiglass
Teflon

⇒ Condensation polymerisation of __________ produces bakelite.
propylene
phenol & formaldehyde
phenol & acetaldehyde
urea & formaldehyde

⇒ Synthetic rubber
deforms, if stretched to double of its original dimension.
is brittle at low temperature
is softer at higher temperature.
is highly permeable to air & water and is readily attacked by chemicals & atmospheric gases.

⇒ Due to its excellent permeability to air/gas and oxidation resistance, the tubes of automobile tyres is made of
cold SBR
butyl rubber
Bunai N
Buna S

⇒ Polymethyl methacrylate (PMMA) is known as
bakelite
teflon
perspex
nylon-6