Question is ⇒ The forbidden energy gap between the valence band and conduction band will be least in case of, Options are ⇒ (A) metals, (B) semiconductors, (C) insulators, (D) all of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ The forbidden energy gap between the valence band and conduction band will be least in case of, Options are ⇒ (A) metals, (B) semiconductors, (C) insulators, (D) all of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The forbidden energy gap between the valence band and conduction band will be least in case of
A.	metals [Correct Answer]
B.	semiconductors [Wrong Answer]
C.	insulators [Wrong Answer]
D.	all of the above [Wrong Answer]
View Answer 2 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If a signal f(t/2) has energy is E/n then energy of the signal f(nt) is equal to __________ (n is constant)
E/2n²
2E/n²
E/n²
2En²

⇒ Which of the following is not valid in case of FETs?
It has low voltage gain
It has high input impedance
It has fast switching time
It is voltage controlled device

⇒ The circuit of the given figur
full adder
magnitude comparator
parity detector
none of the above

⇒ DC ampere hour meter is an indicating instrument.
TRUE
FALSE

⇒ When a ferromagnetic substance is magnetised, there are small changes in its dimensions. This phenomenon is called
hysteresis
magnetostriction
diamagnetism
bipolar relaxation

⇒ Each kilometer of travel in electromagnetic radiation means a time delay of
330 μs
33 μs
3.3 μs
0.33 μs

⇒ A sinusoidal current having peak value of 7.07 A is superimposed on dc of 5A. If a hot-wire ammeter is used to measure the combined current in the circuit, it will indicate __________ ampere.
7.07
10
12.07
2.07

⇒ Class A and Class B power amplifiers predominate at
audio frequencies
radio frequencies
all frequencies
audio and radio frequency

⇒ The Boolean function/implemented in the figure using two I/P multiplexer
ABC + ABC
ABC + AB C
ABC + ABC
ABC + AB C

⇒ Temperature is analogous to
voltage
flux
charge
none of the above

⇒ The terms RMS and average values apply only to sine waves.
TRUE
FALSE

⇒ In a bridge rectifier circuit the rms value of input ac voltage is 10 V. The PIV across each diode is
7.07 V
14.14 V
10 V
28.28 V

⇒ In a circular waveguide with radius r, the dominant mode is
TM₀₁
TE₀₁
TM₁₁
TE₁₁

⇒ Which of the following is a valid real constant in FORTRAN 77?
1.2 E 231
3 E - 2
-3.2 E 2.3
1.2 E 23

⇒ Which factor determines whether the medium is free space, lossless dielectric, lossy dielectric or good conductor?
Attenuation constant
Constitutive parameters (σ, μ, ε)
Loss tangent
Reflection coefficient

⇒ In the TTL circuit in the figure, S₂ to S₀ are select lines and X₇ to X₀ are input lines. S₀ and X₀ are LSBs. The output
Indeterminate
A ⊕ B
A ⊕ B
C . A ⊕ B + C . (A ⊕ B)

⇒ The maximum counting range of a four stage counter using IC 74193 is
0 to 1023
0 to 4093
0 to 65535
0 to 131071

⇒ The impulse response h(t) of a linear time-invariant continuous time system is described by h(t) = exp (at) u(t) + exp (βt) u (- t), where u(t) denotes the unit step function, and a and β are constants. This system is stable if
a is positive and β is positive
a is negative and β is negative
a is positive and β is negative
a is negative and β is positive

⇒ A single phase half wave converter is feeding a resistive load. Output dc power is P_dc and total power delivered to load is P_ac then
P_dc = P_ac for all values of firing angles
P_dc = P_ac if firing angle is less than 180°
P_dc < P_ac for all values of firing angles
P_dc < P_ac if firing angle is less than 180°

⇒ Some possible disadvantages of high level modulation in TV transmitters are

Video monitor has to supply high video voltages upto several hundred volts into highly capacitive loads drawing high current at video frequencies
The grid modulated stage presents a varying load to its driver
The linearity and high video driving power present design problems

Out of above which are true?
1 only
1 and 2 only
1, 2 and 3
2 and 3 only

⇒ The divergence of a vector is a scalar, while the curl of a vector is another
scalar
vector
unit vector
none of the above

⇒ An incremental model of a solid state device is one which represents the
ac property of the device at desired operating point
dc property of the device at all operating points
complete ac and dc behaviour at all operating points
ac property of the device at all operating points

⇒ In 8085 microprocessor, what is the memory address stored on the stack, when the program is interrup
0210 H
0.211 H
0118 H
020 FH

⇒ If x = 0.1396 radians, the values of 1 - cos x and 2 sin² (x / 2) using floating point arithmetic with a 4 digit mantissa are respectively
.1000 E - 1 each
.9727 E - 2 each
.1000 E - 1 and .9727 E - 2 respectively
.9727 E - 2 and .1000 E - 1 respectively

⇒ A 3 phase induction motor is fed by a 3 phase ac regulator to change the stator voltage. The variation in speed will be more if
load torque is constant
load torque increases with increase in speed
load torque decreases with increase in speed
either (a) or (b)

⇒ Which of the transistor models is most preferred for the analysis of a transistor circuit both at mid-band and at high frequencies?
h-parameter model
y-parameter model
s-parameter model
hybrid-p model

⇒ For operation of enhancement only N-channel MOSFET, value of gate voltage has to be
zero
low positive
high negative
high positive

⇒ In the given figure the line voltage after a number of reflections wil
30 V
-30 V
10 V
-10 V

⇒ In TE₁₀ mode of rectangular waveguide
there is one half sine wave variation along x direction and one along y direction
there is one half sine wave variation along y direction and one along x direction
there is one full sine wave variation along x direction and one along y direction
none of the above

⇒ A (75 - J50) ohm load is connected to a coaxial of Z₀ = 75 ohm at 10 GHz. The best method of matching is to connect
an inductance at load
a short circuited stub at load
a short circuited stub at specific distance from load
a capacitance at specific distance from load