Question is ⇒ In a series inverter, Options are ⇒ (A) the commutating elements carry full load current, (B) the commutating elements carry upto 50% of load current, (C) the commutating elements do not carry load current, (D) any of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ In a series inverter, Options are ⇒ (A) the commutating elements carry full load current, (B) the commutating elements carry upto 50% of load current, (C) the commutating elements do not carry load current, (D) any of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a series inverter
A.	the commutating elements carry full load current [Correct Answer]
B.	the commutating elements carry upto 50% of load current [Wrong Answer]
C.	the commutating elements do not carry load current [Wrong Answer]
D.	any of the above [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Impedance inversion may be obtained with
half wave line
a short circuited stub
complex impedance Z connected in series with line
quarter wave line

⇒ The peak factor is the ratio of
peak and rms values
peak and average values
rms and average values
none of the above

⇒ The contents of stack location after the call operation wil
111
1110
1010
1111

⇒ The bandwidth of DSB suppressed carrier modulation system when the modulating frequency varies between 500 Hz and 5 kHz is
555 kHz
505 kHz
500 kHz
9 kHz

⇒ A copper coil has a resistance of 40 ohm at 20°C. At 100°C the resistance is likely to be
44 Ω
54 Ω
84 Ω
104 Ω

⇒ The main difference between the broadside arrays and end fire arrays is that
individual elements are fed with same current in broadside arrays and of different magnitude in end fire arrays
in broadside arrays the elements are equidistant whereas in end fire array the distance between elements increases progressively
the total number of elements in broadside array is always one and a half times that of elements in end fire arrays
in broadside array the individual elements are fed in, out of phase by 180° whereas in end fire array individual elements are fed with currents of equal magnitude but their phases vary progressively along the line in such a way as to make the entire arrangement substantially unidirectional

⇒ The main purpose of using transformer coupling in a class A amplifier is to make it more
efficient
less costly
less bulky
distortion free

⇒ Shifting digits from left to right and vice versa is needed in
storing numbers
arithmetic operations
counting
storing and counting

⇒ In practical commercial FM system, channel bandwidth is
150 kHz
100 kHz
88 MHz
108 MHz

⇒ If carrier modulated by a digital bit stream had one of the possible phases of 0°, 90°, 180°, 270°, then the modulation is called.
BPSK
QPSK
QAM
MSK

⇒ In figure, I_D = 4 mA. Then V_{DS20 V
16 V
4 V
0.4 V}

⇒ Consider the circ
0
(C + D)
1
(A + B) + (C + D)

⇒ SSB-SC stands for
Single Side Band-Suppressed Carrier
Single Side Band-Synchronous Carrier
Synchronous Side Band-Suppressed Carrier
Synchronous Side Band-Self Carrier

⇒ If the output current wave shape of class C circuit has a period of 1 μs and a pulse width of 0.006 μs, the duty cycle is
0.06
0.006
0.00006
0.0006

⇒ Which of the following operations will give the result 2 in C?
42857
4.0 / 2
4.0 / 2.0
4 / 2.0

⇒ In a high frequency coaxial line and the length of line characteristic impedance is a function of
properties of insulating material only
inner and outer conductor radius only
both (a) and (b)
neither (a) nor (b)

⇒ In case of low level amplitude modulation system, the amplifiers following the modulated stage must be
class C amplifiers
linear devices
non-linear devices
harmonic devices

⇒ The static equalisation circuit for thyristors connected in series is
one resistor in series with each thyristor
one resistor in parallel with each thyristor
one resistor and one capacitor in parallel with each thyristor
none of the above

⇒ Microwave resonators are used in
microwave oscillators
microwave narrow band amplifier
microwave frequency metres
all of the above

⇒ Consider a loss less antenna with a directive gain of + 6 dB. If 1 mW of power is fed to it the total power radiated by the antenna will be
4 mW
1 mW
7 mW
1/4 mW

⇒

Assertion (A): TTL uses multiple emitter transistor.

Reason (R): Multiple emitter transistors with about 60 emitters have been developed.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ For 2 port reciprocal network, o.c. output voltage divided by input current is equal to
B
z₁₂
1/y₁₂
h₁₂

⇒ A vibration galvanometer is a
moving coil instrument
moving iron instrument
dynamometer instrument
induction instrument

⇒ Measurement of Hall coefficient enables the determination of
recovery time of stored carrier
type of conductivity and concentration of charge carriers
temperature coefficient and thermal conductivity
Fermi level and forbidden energy gap

⇒ Internet is a worldwide network of computers where most of the information is freely available.
TRUE
FALSE

⇒ In a second order system, peak overshoot is independent of
damping factor
natural frequency
both damping factor and natural frequency
neither damping factor nor natural frequency

⇒

Assertion (A): Two terminal black boxes of R and C can be identified by plotting their static V-I characteristics.

Reason (R): The V-I characteristic of resistance is a straight line of slope R passing through origin.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ In a homogeneous magnetic field H of a solenoid, the core carries a magnetic dipole moment M per unit volume equal to
μ₀ H
μ_r H
(μ_r - 1) H
μ_oμ_r H

⇒ In case of synchro error detector the electrical zero position of control transformer is obtained when angular displacement between rotors is
zero
45°
90°
180°

⇒ If two time varying signals of equal magnitude and zero phase displacement are applied to X and Y plates respectively; of CRO, the display will be
a straight line
a circle
an ellipse
a square