Question is ⇒ Which family of logic circuits uses field effect transistors?, Options are ⇒ (A) TTL, (B) CMOS, (C) Both LED and well as LCD, (D) None of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ Which family of logic circuits uses field effect transistors?, Options are ⇒ (A) TTL, (B) CMOS, (C) Both LED and well as LCD, (D) None of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which family of logic circuits uses field effect transistors?
A.	TTL [Wrong Answer]
B.	CMOS [Correct Answer]
C.	Both LED and well as LCD [Wrong Answer]
D.	None of the above [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Surface impedance at high frequencies is a consideration for
ferrites
semiconductors
good conductors
dielectrics

⇒ For F₂ layer the critical frequency is about
500 MHz
100 MHz
25 MHz
10 MHz

⇒ Nichrome is used for
overload line wires
heater coils
lamp filaments
all of the above

⇒ For the system of the given figure the closed loop poles are locate
s = 0 and s = -2
s = 0, s = -l ± j3
s = -1 ± j3
s = -2 and s = -1 ± j3

⇒ Inductors used at V.H.F. are made using
air core
cast iron cored
sheet steel cored
thin film technique

⇒ In a high frequency coaxial line and the length of line characteristic impedance is a function of
properties of insulating material only
inner and outer conductor radius only
both (a) and (b)
neither (a) nor (b)

⇒ A differential amplifier consists of two CB amplifiers.
TRUE
FALSE

⇒ Which of the following Boolean algebra rules is correct?
A . A = 1
A + AB = A + B
A + A B = A + B
A(A + B) = B

⇒ The magnitude response of a normalised Butterworth low pass filter is
linear starting with value of unity at zero frequency and 0.707 at cut off frequency
non linear all through but with values of unity at zero frequency and 0.707 at cut off frequency
linear upto cut off frequency and nonlinear thereafter
nonlinear upto cut off frequency and linear thereafter

⇒ In amplitude modulation, carrier signals A cos ωt has its amplitude A modulated in proportion with message bearing (low frequency) signal m(t). The magnitude of m(t) is chosen to be __________ .
less than 1
less than or equal to 1
more than 1
none of these

⇒ Which of these has poor overload capacity?
PMMC instrument
Hot wire instrument
Dynamometer instrument
Both (a) and (c)

⇒ A computer program is used to read N and print the sum 1² + 2² + 3² +.....+ N². If N = 10, the print out will show the number
100
10
385
285

⇒ A silicon diode is forward biased and total applied voltage is 5 V. The voltage across p-n junction is
5 V
Slightly less than 5 V
0.7 V
0

⇒

Assertion (A): A large negative feedback is deliberately introduced in an amplifier to make its gain independent of variation is in parameters of active device and other components.

Reason (R): A large negative feedback results in a high value of return difference compared to unity which makes the feedback gain inversely proportional to feedback factor.

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ If γ = (S₀/N₀)/(S_i/N_m) where S₀ and S₁ are signal power output and signal power input and N₀ and N_m are noise power output and noise power input, the value of γ for SSB-SC and DSB-SC amplitude modulated system respectively are
1 and 1
1 and 2
2 and 1
0.5 and 0.5

⇒ A multivibrator generates
sinusoidal waveforms
non-sinusoidal waveforms
both (a) and (b)
none of the above

⇒ The signal cos ω_ct + 0.5 cos ω_mt sin ω_ct is
FM only
AM only
both AM & FM
neither AM nor FM

⇒ Signal to noise ratio of microphone is defined as the ratio of output when the sound pressure is __________ to the output in the absence of any sound signal.
0.5 Pa
0.2 Pa
0.1 Pa
0.01 Pa

⇒ Bitter powder patterns prove the existence of domains.
TRUE
FALSE

⇒ In a radio detector
stabilization against signal strength variation is provided
linearity is worse than in a phase discriminator
the circuit is the same as in discriminator except that diodes are reversed
output is twice that obtainable from a similar phase discriminator

⇒ In a reactance function
all poles are simple
all poles and zeros are simple
all poles and zeros are simple and lie on jω axis only
all poles and zeros lie on negative real axis

⇒ Which one of following is correct condition to check the stability of system?
Bounded I/P unbounded O/P
Bounded I/P and O/P
Bounded O/P and I/P
Bounded I/P Bounded O/P

⇒

Assertion (A): Copper is a good conductor of electricity.

Reason (R): Copper has a face centred cubic lattice.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ To produce p type semiconductor we add
acceptor atoms
donor atoms
pentavalent impurity
trivalent impurity

⇒ Given below impulse response of two sys
h₁(n) non causal and stable
h₁(n) non causal and stable
h₁(n) causal and not stable
h₁(n) causal and stable

⇒ In ac bridge measurements, 'Wagner ground' means
a special RC connection to eliminate stray magnetic effects
a special RC connection to eliminate stray capacitance effects
an unwanted and unintended ground connection
a large metal plate buried in ground connected to one corner of bridge

⇒ Linear diode detector utilizes
linear portion of static characteristics of diode
linear portion of dynamic characteristic of diode
square law portion of dynamic characteristics of diode
rectification property of diode

⇒ Which of the following modes in circular waveguides are circularly symmetric?
TE₀₁
TE₀₂
both (a) and (b)
neither (a) nor (b)

⇒ In an n channel JFET, V_GS = V_GS(off). Then
I_D is zero
I_D may be zero or positive
I_D is positive
I_D may be zero or negative

⇒ Find the FSV (full scale voltage) in a 6 bit R-2R ladder D/A converter has a reference voltage of 6.5 V.
6.4 V
0.1 V
7 V
8 V