Question is ⇒ The filter in figure, uses ideal op-amp. I, Options are ⇒ (A) low pass filter, (B) high pass filter, (C) band pass filter, (D) band stop filter, (E) , Leave your comments or Download question paper.

Question is ⇒ The filter in figure, uses ideal op-amp. I, Options are ⇒ (A) low pass filter, (B) high pass filter, (C) band pass filter, (D) band stop filter, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The filter in figure, uses ideal op-amp. I
A.	low pass filter [Correct Answer]
B.	high pass filter [Wrong Answer]
C.	band pass filter [Wrong Answer]
D.	band stop filter [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the expression a = 5 * 2 / 3.2 + 4 / 8 - 2 + 5 / 9 which operation will have the first priority in C?
5*2
2 / 3.2
5 * 2 / 3.2
42833

⇒ An homogeneous dielectric material is subjected to an electric field E. If a small cavity is made inside the material, the electric field intensity inside and outside the cavity are different.
TRUE
FALSE

⇒ In telecast
video and audio signals are frequency modulated
video signals are frequency modulated but audio signals are amplitude modulated
both audio and video signals are amplitude modulated
video signals are amplitude modulated and audio signals are frequency modulated

⇒ Which of the following is true about an impulse voltage?
It is a unidirectional voltage
Chopped impulse flashover does not occur
Time taken to rise is equal to time taken to fall
RMS value is always less than 50% of average value

⇒ In standard TTL, the 'totem pole' stage refers to
the multi-emitter I/P stage
phase splitter
the O/P buffer
open collector O/P stage

⇒ Costa's receiver is used for
coherent detection of AM-SC signal
asynchronous detection of AM-SC signal
amplitude modulation of signal
frequency modulation of signal

⇒ The V-i relation for a varistor is
i = kvⁿ
v = kiⁿ
i = kv³
v = ki³

⇒ At room temperature kT = 0.03 eV.
TRUE
FALSE

⇒ In a semi-conductor diode, the barrier offers opposition to
holes in P-region only
free electrons in N-region only
majority carriers in both regions
majority as well as minority carriers in both regions

⇒ Which of the following is invalid integer variable name in Fortran?
IAEG
I 124
AILG
MI AC

⇒ Poynting vector is associated with which of the following?
Power flow in electromagnetic
Flux in magnetic field
Charge in electrostatic field
Current in electrostatic field

⇒ The charge of an electron is
1.6 x 10^-17 coulomb
1.6 x 10^-19 coulomb
1.6 x 10^-21 coulomb
1.6 x 10^-23 coulomb

⇒ In the 8421 BCD code, the decimal number 125, is written as
1111101
0001 0010 0101
7 D
none of these

⇒ The ROC of sequence in the Z.T. of sequence x[n] = aⁿ ∪ [n] is
z > a
z < a
|z| > a
|z| < a

⇒ In using mesh current method it is necessary that at least one mesh current links every element.
TRUE
FALSE

⇒ Consider the following statements regarding negative feedback

It increases system gain
It improves sensitivity
It improves system stability

Which of these are not correct?
all
1, 2
1, 3
1 only

⇒ The time constant of the circuit in figur
RC
2 RC
3 RC
5 RC

⇒ The percentage saving in power of 100% modulated suppressed carrier AM signal is
100
75
66.6
50

⇒

Match the following:

	List I		List II
A.	Detection of a periodic signal in noise	1.	Increase in band-width
B.	Recovery of a band limited signal from its uniformly sampled values	2.	Slope over load error
C.	Finer quantization	3.	Nyquist rate of signals
D.	Delta modulation	4.	Cross correlation

A-4, B-3, C-1, D-2
A-3, B-2, C-1, D-4
A-4, B-3, C-2, D-1
A-3, B-2, C-4, D-1

⇒ If the differential voltage gain and the common mode voltage gain of a differential amplifier are 48 dB and 2 dB respectively, then its common mode rejection ratio is
23 dB
25 dB
46 dB
50 dB

⇒ A steel bar needs 1200 AT to magnetise it. The voltage that must be applied to the magnetising coil of 100 turns and 10 Ω resistance is __________ volt.
120
12
1200
10

⇒ The factor which will have least effect on the voltage at the load end of a two-wire supply circuit is
length of the circuit
whether supply frequency is 25 Hz or 50 Hz
amount of load on the circuit
cross-section of the circuit wires

⇒ The input gate current of FET is closer to
few amperes
few milli amperes
few microamperes
negligibly smaller value

⇒ In a resistive ac circuit, the current __________ the voltage by __________ .
lags, 90°
lags, 45°
lags, 0°
leads 90°

⇒ For a second order system ω_n is natural frequency, ω_d is frequency of damped oscillations and ζ is damping factor. Then
ω_d = ω_n ξ
ω_d = ω_n (1 - ξ)²
ω_d = ω_n (1 - ξ)^0.5
ω_d = ω_n (1 - ξ²)^0.5

⇒ A JFET
is current controlled device
has low input resistance
has high gate current
is a voltage controlled device

⇒

Assertion (A): C has a large number of library functions classified as arithmetic functions, data conversion functions, character classified functions, string manipulation functions, searching and sorting functions etc.

Reason (R): 8086 uses a segment : offset addressing scheme.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ Electrons within a metal have energy levels from zero to Fermi level E_F.
TRUE
FALSE

⇒ For the network in figure, the correct loop equation for loop
-I₁ + 4I₂ + 11I₃ = 0
I₁ + 4I₂ + 11I₃ = 0
-I₁ - 4I₂ + 11I₃ = 0
I₁ - 4I₂ + 6I₃ = 0

⇒ Electrical contact materials used in switches, brushes, relay must possess
high thermal conductivity and high melting point
low thermal conductivity and low melting point
high thermal conductivity and low melting point
low thermal conductivity and high melting point