Question is ⇒ If RT, Rh represent condition for reciprocity in case of transmission parameter and hybrid parameter respectively and similarly ST, Sh represent condition for symmetry in case of transmission parameter and hybrid parameter respectively then match the followi, Options are ⇒ (A) 1 - c 2 - d 3 - a 4 - f, (B) 1 - c 2 - b 3 - e 4 - d, (C) 1 - e 2 - d 3 - a 4 - b, (D) 1 - e 2 - d 3 - a 4 - f, (E) , Leave your comments or Download question paper.

Question is ⇒ If RT, Rh represent condition for reciprocity in case of transmission parameter and hybrid parameter respectively and similarly ST, Sh represent condition for symmetry in case of transmission parameter and hybrid parameter respectively then match the followi, Options are ⇒ (A) 1 - c 2 - d 3 - a 4 - f, (B) 1 - c 2 - b 3 - e 4 - d, (C) 1 - e 2 - d 3 - a 4 - b, (D) 1 - e 2 - d 3 - a 4 - f, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If R_T, R_h represent condition for reciprocity in case of transmission parameter and hybrid parameter respectively and similarly S_T, S_h represent condition for symmetry in case of transmission parameter and hybrid parameter respectively then match the followi
A.	1 - c 2 - d 3 - a 4 - f [Correct Answer]
B.	1 - c 2 - b 3 - e 4 - d [Wrong Answer]
C.	1 - e 2 - d 3 - a 4 - b [Wrong Answer]
D.	1 - e 2 - d 3 - a 4 - f [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If t_on and t_off are the turn on and turn off times of a thyristor, then
t_on and t_off are almost equal
t_on >> t_off
t_off >> t_on
t_on is about twice t_off

⇒ An inverting voltage feedback is a
voltage amplifier
current amplifier
current to voltage converter
voltage to current converter

⇒ In calculating output impedance of an amplifier the source is replaced by an open circuit.
TRUE
FALSE

⇒ Three resistances of 15 Ω, 10 Ω and 3 Ω are connected in parallel. The overall resistance is
less than 3 Ω
between 15 and 10 Ω
between 10 and 3 Ω
more than 3 Ω

⇒ An electromagnetic wave is incident normally on a dielectric boundary. It is
totally reflected
partially reflected and partially refracted
totally absorbed
none of the above

⇒

Assertion (A): The gate current of an SCR is always in the form of pulses.

Reason (R): The gate losses, in pulse triggering, are low.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ A number given in binary as 0101.01 is to be scaled up 4 times. The scaled up binary is
10101
1.0101
404.04
10.101

⇒ The numerical value of directive gain may lie between
1 and + 1
0 and 1
0 and ∞
1 and ∞

⇒ The saving of power in DSB-SC modulated at 80% is
NIL
0.8
0.7576
0.5

⇒ Which of the following element does not have three valence electrons?
Boron
Aluminium
Gallium
Phosphorus

⇒ Consider the following:

Coupling capacitor
Emitter by-pass capacitor
Emitter to base diffusion capacitance of the BJT
Stray capacitance of the circuit.

Which of these components in a R-C coupled amplifier control the lower cut-off frequency of the amplifier?
1 and 2
2 and 3
3 and 4
l and 4

⇒ Which of the following frequencies has the greatest period?
20 Hz
200 Hz
20 kHz
200 kHz

⇒ The concentration of minority carriers in a semiconductor depends mainly on
the extent of doping
temperature
the applied bias
none of the above

⇒ A two branch parallel tuned circuits has a coil of resistance R and inductance L in one branch and capacitance C in the second branch. The bandwidth is 200 radians/sec. A load of resistance R_L is connected in parallel. The new bandwidth will be
200 rad/sec
more than 200 rad/sec
less than 200 rad/sec
200 rad/sec or less

⇒ In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is
30 V
60 V
15 V
10 V

⇒ Monostable multivibrator is called one-shot or single-shot circuit because it
can be used once
can be used single and not with other circuits.
always returns by itself to its single stable state
changes to quasistable for a fixed period of time upon receipt of triggering signal.

⇒ In a NOT gate the output is always the opposite of the input.
TRUE
FALSE

⇒ Antenna reciprocity is put to use in
radar system
commercial broadcast
TV broadcast system
none of the above

⇒ Which of the following circuits cannot be demodulate SSB?
Product detector
Balanced modulator
Phase discriminator
BFO

⇒ A wavelength of 1 mm could be expected in
VLF
HF
EHF
SHF

⇒ Computer virus is a piece of rough software of unknown origin that
copies itself like a breeding germ
spreads from one machine to another
eats away processing power
all of the above

⇒ The contents of the program counter after the call operation wil
(30F0)_H
(40F0)_H
(50F0)_H
(60F0)_H

⇒ PIN diode has
p⁺ and n layers separated by i layer
p⁺ and n⁺ layers separated by i layer
p^- and n^- layers separated by i layer
none of the above

⇒

Assertion (A): Maxwell bridge is for measuring inductance of medium magnitude.

Reason (R): In Maxwell's bridge the unknown inductance is measured by comparing it with a capacitance.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ Which amplifier will be preferred for highest gain?
Darlington's pair
Single stage amplifier
Cascade amplifier
Depends on the circuitry

⇒ In which of the following logical group instructions of 8085 do the contents of accumulator remain unchanged?
ORA r
ORA M
ORI data
CMP r

⇒ A series RLC circuit has Q = 5. A voltage of 10 V rms is applied to it. At resonance, the voltage across C is
10 V rms
10 V peak
50 V rms
50 V peak

⇒ A first order element yields almost exact duplication only for constant or slowly varying phenomenon.
TRUE
FALSE

⇒ In a pneumatic bellows
the input surface, output surface and side walls are corrugated
the input surface and output surface are flat but the side walls are corrugated
the input surface and side walls are flat but the output surface is corrugated
the input surface and output surface are corrugated but the side walls are flat

⇒ Each instruction in assembly language program has the following fields:

Lable field
Mnemonic field
Operand field
Comment field

The correct sequence of these fields is?
1, 2, 3, 4
1, 2, 4, 3
2, 1, 3, 4
2, 1, 4, 3