Question is ⇒ Multiplex techniques are used for, Options are ⇒ (A) low density communications, (B) low density point-to-point communications, (C) high-density point-to-point communications, (D) all of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ Multiplex techniques are used for, Options are ⇒ (A) low density communications, (B) low density point-to-point communications, (C) high-density point-to-point communications, (D) all of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Multiplex techniques are used for
A.	low density communications [Wrong Answer]
B.	low density point-to-point communications [Wrong Answer]
C.	high-density point-to-point communications [Correct Answer]
D.	all of the above [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A typical error rate on satellite circuits is one bit error in
10⁷
10³
10²
10¹⁰

⇒ In a specimen of n type semiconductor, the initial concentration of holes and electrons is p_no and n_no. When the specimen is subjected to radiation, the hole and electron concentration increase to p_n and n_n. Then
p_n - p_no = n_n - n_no
p_n + p_no = n_n + n_no
p_n - p_no = n_no + n_no
p_n + p_no = n_n - p_no

⇒ The expression given is F(A, B, C, D, E, F, G, H) = Σ(33, 48, 102, 158, 222, 229, 233, 243, 255); then the __________ and __________ minterms are grouped together into dual and variable __________ is reduced using the dual
243, 233, D
222, 158, B
243, 255, A
229, 243, E

⇒ The transistor of following figure in Si diode with a base current of 40 μA and I_CBO = 0, if V_BB = 6V, R_E = 2 kΩ and β = 90, I_BQ = 20 μA then R_{B200 kΩ
265 kΩ
150 kΩ
100 kΩ}

⇒ Which of the following is used as switch?
J-K flip-flop
Master slave J-K flip-flop
T-flip-flop
D-flip-flop

⇒ Consider the frequency modulated signal 10 cos (2p x 10⁵t + 5 sin (2p x 1500t) + 7.5 sin (2p x 1000t) with carrier frequency of 10⁵Hz. The modulation index is
12.5
10
7.5
5

⇒ For a photoconductor with equal electron and hole mobilities and perfect ohmic contacts at the ends, an increase in illumination results in
a change in O.C. voltage
a change in S.C. current
a decrease in resistance
an increase in resistance

⇒ Resistivity of metals is expressed in terms of
μ ohm
μ ohm/cm
μ ohm-cm
μ ohm-cm/°C

⇒ In a broadcast superheterodynes receiver having no RF amplifier, the loaded Q of the antenna coupling circuit is 100. If the intermediate frequency is 455 kHz. The image frequency at 25 MHz will be
24.09 MHz
24.54 MHz
25.45 MHz
25.91 MHz

⇒ The maximum power that can be transferred to the load is resistor R_L from the voltage source in the figur
1 W
10 W
0.25 W
0.5 W

⇒ For maximum unclipped output from a CE amplifier, the Q point should be
at the centre of dc load line
at the centre of ac load line
at the centre of collector current
none of the above

⇒ Resistivity of semiconductors is around 100 Ω-m.
TRUE
FALSE

⇒ In figure, the steady state current through 1H inductanc
Zero
0.125
0.208333333333333
0.25

⇒ Fourier transform o the function f(t) = 1 is
2p δ (ω)
p δ (ω)
δ(ω)/2p
δ(ω)/p

⇒ In the circuit shown, all the transmission line sections are lossless. The Voltage Standing Wave Ration (VSWR) on the 60W lin
1
1.64
2.5
3

⇒ What would be the reading of voltmeter as shown in below figure. The voltmeter has a 0-1 V scale and is a 20000 Ω/V me
0.4545 V
0.082 V
0.82 V
4.54 V

⇒ A medium is said to be isotropic when
∈ = 0
∈ = μ
∈ = σ
∈ is scalar constant

⇒ A linear diode detector uses RC filter. As modulation index increases the maximum permissible value of time constant RC
increases
decreases
remains constant
either (a) or (c)

⇒ When thyristors are connected in parallel, the current distribution may become non-uniform due to
inductive effect of current carrying conductors
capacitive effect of current carrying conductors
both inductive and capacitive effects
none of the above

⇒ A three terminal monolithic IC regulator can be used as
an a adjustable output voltage regulator alone
an adjustable output voltage regulator & a current regulator
a current regulator & a power switch
a current regulator alone

⇒ The semiconductor diode which can be used in switching circuit in microwave range is
PIN diode
Varactor diode
Tunnel diode
Gunn diode

⇒ Audio and video signals are called modulating waves.
TRUE
FALSE

⇒ Which of these instruments is dynamometers type?
Wattmeter
Power factor meter
Frequency meter
Both (a) and (b)

⇒ Consider the following instruments

Tangent galvanometer
Rayleigh current balance
Household energy meter
Hot wire ammeter

Out of above absolute instruments are
1, 2 and 3
1, 2 and 4
1 and 2
2, 3 and 4

⇒ PA radar means
Phased Array radar
Pulsed Array radar
Pulse Amplitude radar
None of the above

⇒ No load d.c. output will be least in case of
half wave rectifier
full wave rectifier
bridge rectifier
three phase full wave rectifier

⇒ The amplifier circuit shown below uses a silicon transistor. The capacitors C_c and C_E can be assumed to be short at signal frequency and the effect of output resistance r₀ can be ignored. If C_E is disconnected from the circuit, which one of the following statements is T
The input resistance R_i increases and the magnitude of voltage gain A_v decreases
The input resistance R_i decreases and the magnitude of voltage gain A_v decreases
Both input resistance R_i and the magnitude of voltage gain A_v decrease
Both input resistance R_i and the magnitude of voltage gain A_v increase

⇒ Consider the followings statements: A multiplier

selects one of the several inputs and steers it to the output
routes the data from a single input to many outputs
converts parallel data into serial data
is a combinational circuit

On the above statements which are correct?
1, 2, 4
2, 3, 4
1, 3, 4
1, 2, 3

⇒ S is closed for a long time and steady state is reached. S is opened at t(0^-). The voltage marked V is V₀ at t = 0⁺ and V_f at t = ∞. Then value of V₀ and V_f are respecti
8, 8
0, 1
4, 0
4, 8

⇒ A loss less line of characteristic impedance Z₀ is terminated in pure reactance of -jZ₀ value. VSWR is
10
2
1
infinity