Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | A signal m(t) with bandwidth 500 Hz is first multiplied by a signal g(t) w |

A. | δ(t) [Wrong Answer] |

B. | m(t) [Correct Answer] |

C. | 0 [Wrong Answer] |

D. | m(t) δ(t) [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ State variable formulation is very suitable for computer solution.

TRUE

FALSE

⇒ If two network is connected in series-parallel connection then

*h*= [

*h*

_{a}] + [

*h*

_{b}]

[

*a*

_{a}] + [

*b*

_{b}]

[Z] = [Z

_{a}] - [Z

_{b}]

none

⇒ While AM has __________ frequencies, FM has __________ number of sidebands.

2, 3

3, 3

3, 5

3, infinite

⇒ Transfer functions of even complicated components can be found by frequency response tests.

TRUE

FALSE

⇒ The type of feedback in the following circuit diag

Voltage shunt

Current-shunt

Voltage series

Current series

⇒ Fourier analysis indicate that a square wave can be represented as

a fundamental sine wave and odd harmonics

a fundamental sine wave and even harmonics

a fundamental sine wave and harmonics

fundamental and subharmonic sine waves

⇒ While keeping the down-link frequency constant, the diameter of a satellite antenna is reduced by half. To offer the same EIRP over the increased coverage area, the

*RF*output power has to be increases by a factor of

2

4

8

16

⇒ If F(

*j*ω) is the Fourier transform of

*f*(

*t*), then

£

*f*(-

*t*) = F(

*j*ω)

£

*f*(-

*t*) = F* (

*j*ω)

£

*f*(-

*t*) = F(-

*j*ω)

£

*f*(-

*t*) = F* (

*- j*ω)

⇒ Epitaxial growth is used in IC

_{s}

because it produces low parasitic capacitance

because it yields back to back isolating

*pn*Junction

to grow single crystal

*n*doped silicon on a single crystal P-type substrate

to grow Selectivity single crystal P doped silicon of one resistivity on a P type substrate of a different resistivity

⇒ In figure, the magnitude

must be more than that of V

_{a}

must be more than that of V

_{b}

must be more than that of V

_{a}or V

_{b}

can be equal to or less than or more than that of V

_{a}or V

_{b}

⇒ An ideal op-amp can amplify dc signals

TRUE

FALSE

⇒ Loading effect is primarily caused by instruments having

high resistance

high sensitivity

low sensitivity

high range

⇒ In Pascal if I = 55, 10 * I div 10 =

55

50

5.5

5

⇒ A direct current can be measured

directly by dc potentiometer

by dc potentiometer in conjunction with a standard resistance

by dc potentiometer in conjunction with volt ratio box

none of the above

⇒ Half power point directions for broadside is

60°

30°

45°

at any angle

⇒ If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be

a voltage source

a current source

both of the above

none of the above

⇒ Elements R, L, C are connected in parallel and excited by a dc current I. If

*i*

_{R},

*i*

_{L}and

*i*

_{C}are the currents through R, L, C respectively then at

*t*= 0

*i*

_{R}>

*i*

_{L}>

*i*

_{C}

*i*

_{L}>

*i*

_{R}>

*i*

_{C}

*i*

_{C}= 0

*i*

_{C}= I

⇒ The number of switching functions of 3 variables are

3

8

16

32

⇒ Find cut off wavelength for mode TE

_{11}in a circular waveguide having radius 2 cm. Assume K'

_{a}= 1.841

4 cm

6.82 cm

8 cm

68.2 cm

⇒ The properties of FETs closely resemble those of a

thermionic valve

P-N-P transistor

N-P-N transistor

UJT

⇒ Consider the following; for a loss-less transmission line we can write,

- Z
_{in}= -*jz*_{0}for a shorted line with*l*= λ/8 - Z
_{in}= ±*j*∞ for a shorted line with*l*= λ/4 - Z
_{in}=*jz*_{0}for an open line with*l*= λ/2 - Z
_{in}= 0 for a matched line of any length

1, 2

2, 3

1, 3

2, 4

⇒ In EPROM integrated dose is defined as

UV light intensity x exposure time in seconds

UV light intensity / exposure time in seconds

exposure time in seconds / UV light intensity

none of the above

⇒ A source of angular frequency 1 rad sec has a source impedance consisting of 1 Ω resistance in series with 1 H inductance. The load that will obtained the maximum power transfer is

1 Ω resistance

1 Ω resistance in parallel with 1 H inductance

1 Ω resistance in series with 1 F capacitor

1 Ω resistance in parallel with 1 F capacitor

⇒

Match the following:

List I (Types of transmission structure) | List II (Modes of propagation) | ||
---|---|---|---|

A. | Strip line | 1. | Quasi TEM |

B. | Hollow rectangular waveguide | 2. | Pure TEM |

C. | Microstrip | 3. | TE/TM |

D. | Corrugated waveguide | 4. | Hybrid |

A-2, B-1, C-3, D-4

A-4, B-1, C-3, D-2

A-2, B-3, C-1, D-4

A-4, B-3, C-1, D-2

⇒ Which one is a non-causal system?

*y*(

*n*) =

*x*(2

*n*)

*y*(

*n*) =

*x*(

*n*/2)

*y*(

*n*) =

*x*(

*n*/2) +

*x*(

*n*)

all

⇒ At

*t*= ∞; V

_{R2}and V

_{C}wil

4, 4

2, 4

0, 2

2, 0

⇒

**Assertion (A):** Points in the *s* plane at which function G(*s*) is not analytic are called singular, points.

**Reason (R):** Singular points at which the function G(*s*) or its derivative approach infinity are called poles.

Both A and R are correct and R is correct explanation of A

Both A and R are correct but R is not correct explanation of A

A is correct but R is wrong

R is correct but A is wrong

⇒ The figure shown below is designed to act as a constant current source across the load resistor. The β of transistor is 50. What is the value of load curr

1.96 mA

2 mA

2.04 mA

None

⇒ If any term in the first column of a Routh array becomes zero, then

Routh criterion cannot be used to determine stability

Routh criterion can be used by substituting a small positive number for zero and completing the array

Routh criterion can be used by substituting a big positive number for zero and completing the array

Routh criterion can be used by substituting a small negative number for zero and completing the array

⇒ Choose the correct option

- Mesh is the smallest loop of circuit
- Loop is smallest path of circuit
- Loop does not contain any mesh
- Loop may have one or more than one mesh

1, 2, 3, 4

3, 4, 2

1, 4

3, 2