Question is ⇒ Which of the following is not correct?, Options are ⇒ (A) Voltmeter should have a very high resistance, (B) An ammeter should have a very low resistance, (C) A shunt should have a very low resistance, (D) An electronic voltmeter draws appreciable current from source, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following is not correct?, Options are ⇒ (A) Voltmeter should have a very high resistance, (B) An ammeter should have a very low resistance, (C) A shunt should have a very low resistance, (D) An electronic voltmeter draws appreciable current from source, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following is not correct?
A.	Voltmeter should have a very high resistance [Wrong Answer]
B.	An ammeter should have a very low resistance [Wrong Answer]
C.	A shunt should have a very low resistance [Wrong Answer]
D.	An electronic voltmeter draws appreciable current from source [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A three terminal monolithic IC regulator can be used as
an a adjustable output voltage regulator alone
an adjustable output voltage regulator & a current regulator
a current regulator & a power switch
a current regulator alone

⇒ Some of MOS families are PMOS, NMOS, CMOS. The family dominating the LSI field where low power consumption is necessary is
NMOS
CMOS
PMOS
both NMOS and CMOS

⇒ A standard waveguide W R90 has inside wall dimensions of a = 2.286 cm and b = 1.016 cm. What is the cut-off wavelength for TE₀₁ mode?
4.572 cm
2.286 cm
2.032 cm
1.857 cm

⇒ Assuming accumulator contain A 64 and the carry is set (1). What will register A and (CY) contain after SBI 0B7H?
12 H, 0
12 H, 1
DDH, 0
DDH, 1

⇒ A microwave junction is matched at all ports if the S matrix
has all diagonal elements zero
has all diagonal elements equal but not zero
has all diagonal elements complex
is Hermitian

⇒ For the power amplifier circuit shown below, the maximum power dissipated by both output transisto
9.66 W
30.11 W
31.66 W
33.66 W

⇒ Silicon and germanium are elements in the
second column of periodic table
third column of periodic table
fourth column of periodic table
fifth column of periodic table

⇒ An unmodulated voltage 10 V effective is applied to a dioxide detector in which load resistance is 4 x 10^-5 ohms. A micrometer shows that the rectified DC current in this resistance is 30 A. The efficiency of detection is
0.34
0.555
0.688
0.847

⇒ With a JK master-slave flip-flop the master is clocked when the clock is __________ , and the slave is triggered when the clock is __________ .
low, low
high, low
low, high
high, high

⇒ L/C has the dimension of
time
capacitance
inductance
resistance

⇒ In the following transistor circuit V_BE = 0. 7 V, r_c = 25mV/I_E, and β and the capacitance are very l
-180
-120
-90
-60

⇒ Electronic tubes used for transmitter differ from their counterparts in the receivers in respect that
they are large in size
they are capable of handling large powers
they generate large amount of heat when in operation
none of the above

⇒ The maximum percent overshoot with maximum value of first overshoot as 3.5 V and steady state value as 2.575 V is
0.3592
0.2643
0.5761
0.1524

⇒ A 'n' bit sequence generator employing SR flip-flop has maximum length of the sequence as :
2ⁿ
n
2ⁿ - 1
2ⁿ^-1

⇒ A communication channel with additive white Gaussian noise, has a bandwidth of 4 kHz and an SNR of 15. Its channel capacity is
1.6 kbps
16 kbps
32 kbps
256 kbps

⇒ A rectangular waveguide, in dominant TE mode, has dimensions 10 cm x 15 cm. The cut off frequency is
10 GHz
1 GHz
15 GHz
25 GHz

⇒ Some possible functions of AGC in a TV receiver are

To increase gain for weak signals
To decrease gain for strong signals
To change the contrast when we switch from one channel to other
To reduce flutter

Which of the above are correct?
1, 2, 3, 4
1, 2, 4
1, 2, 3
2, 3, 4

⇒ The current in an RL series circuit is 1 - e^-t amperes. Then di/dt is
1 - e^-t
- e^-t
e^t
e^-2t

⇒ Which of the following is not correct?
In SSB amplitude modulated system, the transmitter circuit has to be more stable leading to better reception
In SSB amplitude modulated system more channel space is available as compared to double sideband amplitude modulated system
In SSB amplitude modulated system the signal is more noise resistant as compared to double sideband system
An SSB-AM system requires lesser power (for the same signal strength) as compared to DSB-AM system

⇒

Assertion (A): Static RAMS are used where speed of operation is of primary concern.

Reason (R): Dynamic RAM has lower cost per bit than static RAM.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ In TV scanning sequence of lines is
left to right
right to left
left to right for odd fields and right to left for even field
left to right for even fields and right to left for odd field

⇒ How many different binary numbers can be stored in a register consisting of six switches?
16
32
64
128

⇒ Which of the following logic no resistors are used?
CMOS
TTL
4 n sec ECL
8 sec ECL

⇒ Tropospheric scatter propagation is not subject to any fading.
TRUE
FALSE

⇒ I-PD controlled system has
I, P and D actions in forward path
I, P and D actions in feedback path
I action in forward path but P and D action in feedback path
I action in feedback path but P and D actioins in forward path

⇒ Hall effect is observed in a specimen when it is carrying current and is placed in a magnetic field. The resulting electric field inside the speciment will be in
direction normal to both current and magnetic field
the direction of current
direction antiparallel to magnetic field
an arbitrary direction depend upon conductivity

⇒ A discrete zero memory information source has 40 symbols and each symbol is equally likely. The minimum number of bits required to code the source with uniform length code and entropy of the source are
5 and 5.03
6 and 5.83
5 and 6.64
6 and 5.32

⇒ The poles with greater displacement from the real axis correspond to
higher frequencies of oscillation
stable response
lower frequencies of oscillation
unbounded output

⇒ When a TTL is driving an CMOS gates it is necessary to ensure that
V_OL(for TTL) ≤ V_IL (for CMOS) and V_0H (for TTL) ≥ VIH (for CMOS)
V_0L (for TTL) ≥ V_IL (for CMOS)
V_0H (for TTL) ≤ V_IH (for CMOS)
V_0L (for TTL) ≥ V_IL (for CMOS) and V_0H (for TTL) ≤ VIH (for CMOS)

⇒ For a photoengraving the mask used is
master mask
slave mask
working mask
photo mask