Question is ⇒ Reflection from the object to be measured is significant only when the wavelength is, Options are ⇒ (A) much bigger than the size of object, (B) much smaller than the size of object, (C) almost of the size of object, (D) either (a) or (c), (E) , Leave your comments or Download question paper.

Question is ⇒ Reflection from the object to be measured is significant only when the wavelength is, Options are ⇒ (A) much bigger than the size of object, (B) much smaller than the size of object, (C) almost of the size of object, (D) either (a) or (c), (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Reflection from the object to be measured is significant only when the wavelength is
A.	much bigger than the size of object [Wrong Answer]
B.	much smaller than the size of object [Correct Answer]
C.	almost of the size of object [Wrong Answer]
D.	either (a) or (c) [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For the given truth table, the correct Boolean expressio
XYZ + X YZ + X Y Z
X Y Z + XYZ + X YZ
X Y Z + XYZ + XY Z
XYZ + XYZ + XY Z

⇒ The radiation pattern of Hertzian dipole in the plane perpendicular to dipole is a
null
circle
figure of eight
none of the above

⇒ Geosynchronous satellites are always launched in the equatorial plane because it is the only plane which provides
24-hour orbit
stationary satellite
global communication
zero-gravity environs

⇒ Consider the following statements regarding phase sensitive detector

The detector reads zero when phases of input signal and reference signal are different.
The detector acts as a linear rectifier.
The detector can be used as vector voltmeter.

Of the above statements which are correct?
1, 2, 3
1 and 2
2 and 3
1 and 3

⇒ The system of the given fi
has two poles and one zero in left half plane
has two poles and one zero in right half plane
has two poles in left half plane and zero in right half plane
none of the above

⇒ A voltage wave is v = 50 sin ωt. Its average value calculated over full one cycle is
zero
35.36 V
31.85 V
none of the above

⇒ Calculate the stability factor and change in I_c from 25°C to 100°C for, β = 50, R_B/R_E = 250, ΔI_CO = 19.9 nA for emitter bias configuration
42.553, 0.85 μF
40.91, 0.58 μF
38.53, 0.85 μF
41.10, 0.39 μF

⇒ A short vertical grounded antenna is required to radiate at 1 MHz. The effective height of the antenna is 302 m. The calculated value of radiation resistance is
1.58 Ω
158 Ω
15.8 Ω
none

⇒ Measurement of Hall coefficient enables the determination of
transportation factor decreases and a increases
transportation factor increases and a increases
transportation factor increases and a decreases
transportation factor decreases and a decreases

⇒ A material for permanent magnet should have
High retentivity
High permeability
Low hysteresis loss
High hysteresis loss

⇒ TE₁₀ mode of propagation of electromagnetic energy in waveguides can be thought of as
three TEM waves travelling along length of wave-guide
One TEM wave travelling along length of wave guide and one TEM wave propagation in the transverse plane
One TEM wave travelling along the length of wave guide and two TEM waves
none of the above

⇒ Which amplifier has a voltage gain of less than 1?
Common emitter
Common collector
Common base
Both CB and CC

⇒ A choke coil of resistance R and inductance L is shunted by capacitor C. The dynamic resistance is
R/LC
C/RL
L/RC
1/RLC

⇒ In force current analogue, mechanical mobility is analogous to
impedance Z
admittance Y
reactance X
conductance G

⇒ A quarter wave line open circuited at far end behaves as
inductance
L and C in parallel
capacitance
L and C in series

⇒ In a FM signal, the modulation index increases, then the power
increases
decreases
remains constant
none of the above

⇒ A copper specimen has resistivity equal to 1.8 x 10^-8 ohm-m at room temperature. At a temperature of 700 K, the resistivity is likely to be
1.6 x 10^-8 Ω-m
2 x 10^-8 Ω-m
3 x 10^-8 Ω-m
6 x 10^-8 Ω-m

⇒ A particular current is made up of two components 10A dc and sinusoidal current of peak value 14.14A. The average of resultant current is
zero
24.14A
10A
14.14A

⇒ Which of the following operations will give the result 2 in C?
42857
4.0 / 2
4.0 / 2.0
4 / 2.0

⇒ Which of the following logic family is fastest of all?
TTL
RTL
DCTL
ECL

⇒ Figure shows a NAND latch used as a switch debouncer. With the switch in STOP position. Q will be equal to
0
1
CLK
none of these

⇒ Consider the following two statements about the internal conditions in an n-channel MOSFET operating in the active re
Only S2 is true
Both S1 and S2 are false
Both S1 and S2 are true, but S2 is not a reason for S1
Both S1 and S2 are true, and S2 is a reason for S1

⇒ Which one of the following effects is used in measuring power?
Seeback
Ferrari
Induction
Hall

⇒

Assertion (A): Class A and Class B amplifier predominate in audio applications.

Reason (R): Class C amplifier is used at radio frequencies.

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ The inductance of a twin feeder used to connect antenna to TV receiver is about
0.2 μ H/m
0.6 μ H/m
1.6 μ H/m
10 μ H/m

⇒ Macroscopic quantities of a given material
are absolutely constant
are a function of temperature
are a function of temperature, pressure field
none of the above

⇒ For a second order system the damping factor is varied from 0 to 1. The locus of poles is
a straight line on imaginary axis
a straight line on real axis
a semi circle
a circle

⇒ Which of the following is not a DTP program?
Page maker
Coral draw
Coral ventura
Coral key

⇒ In the given figure shows a 3 bit shift register using TTL flip flops. Initially all the flip flops are set to 0 state. After 8 clock pul
A = 1, B = 1, C = 1
A = 1, B = 1, C = 0
A = 0, B = 1, C = 1
A = 0, B = 0, C = 1

⇒ The gate lead, in a thyristor is welded to :
p layer to which anode is connected
n layer nearest to the anode terminal
p layer nearest to the cathode terminal
outside n layer