Question is ⇒ The characteristic impedance of coaxial cable is about, Options are ⇒ (A) 1000 ohm, (B) 500 ohm, (C) 250 ohm, (D) 75 ohm, (E) , Leave your comments or Download question paper.

Question is ⇒ The characteristic impedance of coaxial cable is about, Options are ⇒ (A) 1000 ohm, (B) 500 ohm, (C) 250 ohm, (D) 75 ohm, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The characteristic impedance of coaxial cable is about
A.	1000 ohm [Wrong Answer]
B.	500 ohm [Wrong Answer]
C.	250 ohm [Wrong Answer]
D.	75 ohm [Correct Answer]
View Answer 2 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ CMOS is extensively used in
pocket calculators
digital wrist watches
satellites
all of the above

⇒ If the energy gap of a semiconductor is 1.1 eV, then it would be.
opaque to the visible light
transparent to the visible light
transparent to the ultraviolet radiation
opaque to the infrared radiation

⇒ For the minterm designation Y = ∑ m (1, 3, 5, 7) the complete expression is
Y = A BC + A B C
Y = A B C + A B C + ABC + A BC
Y = A B C + A B C + ABC + A BC
Y = A B C + ABC + A BC + A BC

⇒ In the given figure the number of combinations of three non touching loop
0
1
2
3

⇒ The tape recorders used in homes have
common head and common amplifier system for recording and playback
different heads and amplifiers for recording and playback
same head but different amplifiers for recording and playback
different heads but same amplifier for recording and playback

⇒ A (75 - j 50) Ω load is connected to a coaxial line of Z₀ = 75 Ω at 10 GHz. The best method of matching consists of using
a capacitance at some specific distance from load
a short circuited stub at some specific distance from load
an inductance at load
a short circuited stub at load

⇒ The energy to cause thermionic emission is supplied by heating the cathode.
TRUE
FALSE

⇒ The ratio of diffusion constant for hole D_P to the mobility for holes is proportional to
T²
T
1/T
T³

⇒ An ungrounded antenna near the ground
is horizontally polarized
acts as an antenna array
acts as a single antenna of twice the height
is not likely to need an earth mat

⇒ To protect an SCR against high di/dt we connect
a capacitance in series with SCR
a capacitance in parallel with SCR
an inductance in parallel with SCR
an inductance in series with SCR

⇒ The voltage of single phase supply to residential consumers in India is
400 V
230 V
2.2 kV
11 kV

⇒ The power factor at the input terminals of a cyclo- converter is generally
low and leading
low and lagging
high and leading
high and lagging

⇒

Assertion (A): A two byte instruction of 8085 has an operation code in first byte and operand / address in the second byte.

Reason (R): If an instruction is too long it is possible to reduce its length by a number of methods.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ It is required to increase the maximum range of a radar by a factor of two. The peak power transmitted in the radar system has to be increased by a factor of
2
4
8
16

⇒ To ensure good transient response in audio systems the natural frequencies should be
above 40 Hz and below 15 kHz
above 40 Hz
above 15 kHz
below 40 Hz and above 15 kHz

⇒ Trap circuits used in video IF amplifier of colour TV are
High Q, LC resonant circuit
Low Q, LC resonant circuit
High Q, RLC resonant circuit
Low Q, RLC resonant circuit

⇒ The seven bit Hamming code received is 0010001. If even parity has been used, the correct code is
10001
1110001
110001
11001

⇒ It is desired that transmission line and load should match for a range of frequencies. The best method is
to use a balun
to use a single stub of adjustable position
to use a double stub
to use a broad band amplifier

⇒

Assertion (A): When the anode current of an SCR starts increasing during turn on process, the anode cathode voltage drop starts decreasing.

Reason (R): During turn on the reverse biased junction in SCR breaksdown.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Consider the following symbols

Letters A to Z and a to z
Digits 0 to 9
Logical operators and, or, not
Parenthesis ( )

Which of the above symbols are available in Pascal?
1 and 2 only
1, 2 and 3 only
1, 2 and 4 only
All

⇒ Which of the following is basically a voltage controlled capacitance?
Zener diode
Diode
Varactor diode
LED

⇒

Assertion (A): Dielectric constant is independent of temperature unless the temperature is extremely high.

Reason (R): For normal temperatures the number of atoms per unit volume is constant.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ In which of the following 8085 instructions is the 8 bit number in accumulator adjusted to form two four bit BCD numbers
DAD rp
DAA
DCX rp
ADC M

⇒ The gain of a current element is
0 dB
1.67 dB
1.76 dB
3 dB

⇒ The term critical frequency denotes
the lowest frequency that is reflected by the ionosphere
the highest frequency that is reflected by the ionosphere at vertical distance
the lowest frequency by which communication is possible between two given points
none of the above

⇒ A load commutated chopper circuit has
one thyristor
two thyristors
four thyristors
six thyristors

⇒ Which of the following equations satisfy Maxwell's equations?
E_x = E_y = 0, E_z = cos (y - ct)
E_x = E_y = 0, E_z = cos (y- ct)
F_y = cos (y - ct), E_x = E_z = 0
None of these

⇒ In a series circuit with fixed R and variable X_L, the current locus lies in the fourth quadrant.
TRUE
FALSE

⇒ Which of the following best represents the output impedance of an actual op-amp?
10 ohm
100 ohm
10 k ohm
100 k ohm

⇒ To convert JK flip flop to D flip flop
connect D to both J and K
connect D to J directly and D to K through inverter
connect D to K directly and D to J through inverter
connect D to K and leave J open