Question is ⇒ Automobile ignition systems use the principle of, Options are ⇒ (A) resistance, (B) self inductance, (C) mutual inductance, (D) capacitance, (E) , Leave your comments or Download question paper.

Question is ⇒ Automobile ignition systems use the principle of, Options are ⇒ (A) resistance, (B) self inductance, (C) mutual inductance, (D) capacitance, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Automobile ignition systems use the principle of
A.	resistance [Wrong Answer]
B.	self inductance [Wrong Answer]
C.	mutual inductance [Correct Answer]
D.	capacitance [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a power diode the reverse recovery time is the time from the instant the forward current is zero to the instant when reverse recovery current has decayed to
50% of peak reverse current
25% of peak reverse current
10% of peak reverse current
zero value

⇒ In ac circuits maximum power is delivered to a load if load impedance is conjugate of source impedance.
TRUE
FALSE

⇒ In figure, the battery has remained switched on for a long time. At t = 0 the switch is closed. The current i(t) is likely t
6
6 - 3e^-1
6 + 3e^-1
3 - 6e^-1

⇒ What do the contents of instruction register specify?
Operand for the instruction being executed
Op code for the instruction being executed
Op code for the instruction to be executed next
Operand for the instruction to be executed next

⇒ Which is not purpose of modulation?
Effective radiation
Multiplexing
Narrow band
Increase in signal power

⇒ Self bias is an example of __________ feedback that tends to stabilize the drain current against changes in temperature and JFET replacement.
variable
low
negative
positive

⇒ As compared to a bipolar transistor, a JFET is
highly sensitive to changes in input voltage
more sensitive to changes in input voltage
less sensitive to changes in input voltage
equally sensitive to changes in input voltage

⇒ For a parallel two wire line with both conductors touching each other, the characteristic impedance is about
300 Ω
200 Ω
80 Ω
24 Ω

⇒ A 3 phase balanced supply feeds 3 phase unbalanced load. Power supplied to the load can be measured by using

2 wattmeter
one wattmeter
3 wattmeter

Which of the above statements is correct?
1 and 2
1 and 3
2 and 3
3 alone

⇒ Two sinusoidal signals of equal amplitude and frequency are applied to X and Y plate of CRO respectively. The observed Lissajous pattern is a straight line. The phase shift between signals is
zero
90°
either zero or 180°
either 90° or 270°

⇒ The frequency of oscillation in a backward wave oscillator can be changed by
varying the voltage which controls beam velocity
varying the beam current
both by varying the beam current and by light varying the voltage which controls beam velocity
changing the rate of thermionic emission

⇒ A broadside array consisting of 200 cm wavelength with 10 half-wave dipole spacing 10 cm. And if each array element feeding with 1 amp. current and operating at same frequency then find the radiated power
730 W
73 W
100 W
None

⇒ In a N-P-N transistor the function of the emitter is
to emit or inject holes into the collector
to emit or inject electrons into the collector
to emit or inject electrons into the base
to emit or inject holes into the base

⇒ A line has a phase constant of 29.8 rad/m. At 1000 MHz the wavelength is
29.8 m
2.98 m
2.1 m
0.21 m

⇒ In a full wave diode rectifier circuit each diode carries current for
90° in each cycle
180° in each cycle
270° in each cycle
360° in each cycle

⇒ In a communication receiver, a squelch circuit is normally inserted
before detector
after detector
before mixer
after power amplifier

⇒ CC circuit is suitable for impedance matching.
TRUE
FALSE

⇒ The snubber circuit consists of
a capacitor connected in series with thyristor
a capacitor connected in parallel with thyristor
a resistor and capacitor in series connected across thyristor
none of the above

⇒ Which of the following is a digital modulation technique?
PCM
PSK
DM
All

⇒ The advantage of LVDT over inductive bridge type transducer is that
it gives high output for small changes in core position
it can be used over a temperature range of - 265°C to 600°C
it can measure displacement of moving object
the error due to stray magnetic field is less

⇒ In a coaxial line
the characteristic impedance is less than that of two wire line
the wave velocity is less than that of two wire line
both (a) and (b)
neither (a) nor (b)

⇒ A waveguide twist is used to change the plane of polarization.
TRUE
FALSE

⇒ In 8085 microprocessor with memory mapped I/O which of the following is true?
I/O devices have 16 bit addresses
I/O devices are accessed during IN and OUT instructions
There can be a maximum of 256 input and 256 output devices
Logic operations can not be performed

⇒ A narrow band noise n(t) has symmetrical spectrum and has power density spectrum 0.2 x 10^-6. The power density of quadrature component is
0.2 x 10^-6
10^-7
4 x 10^-7
5 x 10^-8

⇒ Which of the following array names in Fortran 77 is invalid?
A(6)
A(R)
A(I)
A(N)

⇒ The correct sequence of parts in klystron amplifier are
anode, catcher cavity, cathode, buncher cavity
cathode, buncher cavity, catcher cavity, cavity
anode, buncher cavity, catcher cavity, cathode
cathode, catcher cavity, anode, buncher cavity

⇒ What are the ultimate purpose of minimizing logic expressions?

To get small size expression.
To reduce the number of variables in the given expression.
To implement the function of the logic expression with least hardware.
To reduce the expression for making it feasible for hardware implementation.

Select the correct answer from the codes given below:
1 only
2 and 3
3 only
3 and 4

⇒ The frequency range for satellite communication is
3 to 30 kHz
300 to 3000 kHz
3000 to 30000 MHz
30000 to 300000 MHz

⇒ For a Mod-64 synchronous counter the number of flip flops and AND gates needed is
6 and 4 respectively
4 and 6 respectively
7 and 5 respectively
5 and 7 respectively

⇒ In root locus analysis the breakaway and break in points
lie on the real axis
either lie on the real axis or occur in complex conjugate pairs
always occur in complex conjugate pairs
none of the above