Question is ⇒ A step up chopper can give an output voltage, Options are ⇒ (A) higher than input voltage, (B) lower than input voltage, (C) both higher and lower input voltage, (D) all of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ A step up chopper can give an output voltage, Options are ⇒ (A) higher than input voltage, (B) lower than input voltage, (C) both higher and lower input voltage, (D) all of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A step up chopper can give an output voltage
A.	higher than input voltage [Correct Answer]
B.	lower than input voltage [Wrong Answer]
C.	both higher and lower input voltage [Wrong Answer]
D.	all of the above [Wrong Answer]
View Answer 1 -3 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Assertion (A): Magnetic tape can be accessed only sequentially.

Reason (R): Magnetic tape consists of magnetised spots or tracks.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ The main advantage of CMOS circuit is
high gain
high output impedance
low power consumption
high gain and high output impedance

⇒ Quartz crystal has
very small Q
small Q
very high Q
Q less than 1

⇒

Assertion (A): Relaxation time and mean time between collisions are equal when scattering is isotropic.

Reason (R): Mean free path of an electron λ, velocity of electron v and mean time between collisions t_c are related as λ = vT_c.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ A frequency multiplier stage should operate as
class A
class AB
class C
either of the above

⇒ The phase velocity in a coaxial line is
greater than C
equal to C
less than C
not depend on C

⇒ The phase velocity v in a transmission line is
LC
C/L
L/C
1/LC

⇒ In which mode of BJT operation are both junctions reverse biased?
Active
Saturation
Cut off
Reverse active

⇒ Hall effect is observed in a specimen when it is carrying current and is placed in a magnetic field. The resulting electric field inside the speciment will be in
direction normal to both current and magnetic field
the direction of current
direction antiparallel to magnetic field
an arbitrary direction depend upon conductivity

⇒

Assertion (A): When a photoconductive device is exposed to light, its bulk resistance increases.

Reason (R): When exposed to light, electron hole pairs are generated in the photoconductive device.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ If the average power of radar transmitters is 2 kW and the peak power of the transmitter is 1000 kW, what will be the duty cycle?
0.002
0.02
0.001
0.01

⇒ A potential of 7 V is applied to a silicon diode. A resistance of 1 kΩ is also connected in series. If the diode is forward biased, the current in the circuit is
7 mA
6.3 mA
0.7 mA
0

⇒ If C is spring constant and θ is deflection, controlling torque is
Cθ
C/θ
θ/C
C²θ

⇒ If the bandwidth is increased by 2, the γ_FM γ_AM (where γ is the ratio of SNR of output to SNR at input, FM is frequency modulation and AM is amplitude modulation) is increased by a factor of
2
3
4
6

⇒ For the transport lag G(jω) = e^-jωT, the phase angle
is constant
varies linearly with frequency
varies linearly with low frequencies only
values as per square law

⇒ 2N 2430 could be a
semi-conductor diode
dual gate MOSFET
BJT
UJT

⇒ Which one of the following is true for EM wave propagation through rectangular waveguide of cross-section 2a x a
critical wavelength for TE₁₀ mode is the same as that for TE₀₂ mode
critical wavelength for TE₁₀ mode is one half of that for TE₁₀ mode
critical wavelength for TE₁₀ mode is the same as that for TM₁₀ mode
critical wavelength for TE₁₀ mode is double that for TE₀₁mode

⇒ A dielectric does not have leakage current.
TRUE
FALSE

⇒ For a current transformer, the standard secondary rating is
1 A or 5 A
2.5 A
0.416666666666667
5 A or 10 A

⇒ The pressure coil of a wattmeter should be connected to the supply side of the current coil when
load impedance in high
load impedance is low
voltage is high
voltage is low

⇒ The orientation polarization of a polyatomic gas is inversely proportional to absolute temperature.
TRUE
FALSE

⇒ The type of noise that interfere very much with high frequency transmission is
white
transit time
flicker
shot

⇒ The pre-emphasis in FM aids in providing extra noise immunity by
emphasizing only the higher frequency components
emphasizing the entire frequency band
emphasizing only the lower frequency band
cutting down the low frequency noise

⇒ The characteristic equation of an SR flip-flop in given by
Q_n+1 = S + RQ_n
Q_n+1 = RQ_n + SQ_n
Q_n+1 = S + RQ_n
Q_n+1 = S + RQ_n

⇒ Which of the following frequency is likely to be associated with AM radio broadcast?
1000 kHz
100 MHz
500 MHz
10 GHz

⇒ Ridge waveguide is essentially a form of capacitively loaded guide.
TRUE
FALSE

⇒ A rectangular waveguide having TE₁₀ mode as dominant mode is having a cut off frequency of 18 GHz for the TE₃₀ mode. The inner broad wall dimension of the rectangular waveguide is
5/3 cm
5 cm
5/2 cm
10 cm

⇒ In Vidicon camera tube, the resistance of photoconductive material on the target plate
is constant
is more in darkness and less in brightness
is more in brightness but less in darkness and brightness
may be more or less in darkness and brightness

⇒ The intrinsic carrier concentration of silicon sample at 300 K is 1.5 x 10¹⁶/m³. If after doping, the number of majority carriers is 5 x 10²⁰/m³. The minority carrier density is
4.5 x 10¹¹/m³
3.33 x 10⁴/m³
5 x 10²⁰/m³
3 x 10^-5/m³

⇒ In terrestrial microwave links, the number of 'fades' per unit increases as
both the transmission and the distance between the antennas are increased
the transmission frequency is increased but the distance between the antennas is decreased
the transmission frequency is decreased but the distance between the antennas is increased
both the transmission frequency and distance between the antennas are decreased