Question is ⇒ In a CRO, the time base signal is applied to, Options are ⇒ (A) X plates, (B) Y plates, (C) either X or Y plates, (D) alternately X and Y plates, (E) , Leave your comments or Download question paper.

Question is ⇒ In a CRO, the time base signal is applied to, Options are ⇒ (A) X plates, (B) Y plates, (C) either X or Y plates, (D) alternately X and Y plates, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a CRO, the time base signal is applied to
A.	X plates [Correct Answer]
B.	Y plates [Wrong Answer]
C.	either X or Y plates [Wrong Answer]
D.	alternately X and Y plates [Wrong Answer]
View Answer 9 -9 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A moving coil meter has a shunt of 0.02 Ω resistance. If coil resistance is 1000 Ω and a potential difference of 500 mV is required across it to cause full scale deflection, the current through shunt is
2.5 A
25 A
0.25 A
0.025 A

⇒ In brushless excitation system of modern alternators, the main exciter is
dc generator
ac generator
either dc or ac generator
induction generator

⇒ How is inversion achieved using EX-OR gate?
Giving input signal to the two input lines of the gate tied together
Giving input to one input line and logic one to the other line
Giving input to one input line and logic one to the other line
Inversion cannot be achieved using EX-OR gate

⇒ Hay bridge is suitable for measuring inductance of which one of the following inductors?
Having Q value less than 10
Having Q value greater than 10
Having any value of Q
Having phase angle of reactance very large

⇒ In 8086 the flag which enables or disables external interrupts is
IF
DF
TF
CF

⇒ A transmitter serial current contains
carrier frequencies
audio frequencies
radio frequencies
none of the above

⇒ It is very likely in __________ gate family that when one gate is driving number of gates in __________ , a gate having least voltage for saturation may consume large __________ leaving other gates inoperative and this phenomenon is called __________ .
DTL, parallel, current, current - sinking
DCTL, parallel, current, current-lagging
ECL, series, voltage, voltage-deterioration
DCTL, series, current, current-lagging

⇒ In the spectrum of an FM wave
When modulation index is large, carrier frequency disappears
carrier frequency cannot disappear
amplitude of any side band depends on modulation index
the total number of side bands depend on modulation index

⇒ High frequency waves are
absorbed by F₂ layer
affected by solar cycle
reflected by D layer
none of the above

⇒ In one time constant, the current in a circuit reaches __________ percent of its final value.
10
37
63
85

⇒

Assertion (A): R-2R ladder type DAC has higher speed of operation than weighted resistor DAC

Reason (R): R-2R ladder type DAC uses only two different values of resistor network uses many different values of resistors

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In the op-amp circuit of figure, V_{03 V₁ - 4 V₂
-3 V₁ + 4 V₂
3(V₁ - V₂)
-3(V₁ - V₂)}

⇒ In a resistance loaded, RC coupled amplifier the d.c. component is blocked by
Transistor
C_C
R_B
R_C

⇒ A dual trace CRO has
one electron gun
two electron guns
one electron gun with one two pole switch
two electron guns with one two pole switch

⇒ In audio cassettes the width of each recording track is
5 mm
2.5 mm
1.5 mm
1 mm

⇒

Match the following:

	List I		List II
A.	Copper	1.	produces discrete energy level just above valence band
B.	Rubber	2.	produces discrete energy level just below conduction band
C.	Antimony	3.	large forbidden gap
D.	Boron	4.	valence and conduction bands overlap

A-1, B-2, C-4, D-3
A-4, B-1, C-2, D-3
A-4, B-3, C-1, D-2
A-2, B-1, C-3, D-4

⇒ The number of PM radio channels which can be accommodated in a spectrum of 300 MHz is about
10
100
500
1500

⇒ Large scale integration refers to
more than 50 gates on the same chip
more than 80 gates on the same chip
more than 100 gates on the same chip
none of the above

⇒ A clipper
adds a dc component to the input signal
removes signal voltages above or below a specified value
both (a) and (b)
either (a) or (b)

⇒ Consider the following test signal patterns

Ramp
Grill
Grey shades
Sine pulse
Picture line up generating equipment

Which of the above are used in TV studios?
All
1, 2 and 3 only
1, 2 and 5 only
2, 3, 4 and 5 only

⇒

Assertion (A): A dual converter may be circulating current type or non circulating current type.

Reason (R): In circulating current dual converter only one converter can be operated at one time.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Which of the following conditional statements is not valid in Pascal?
If A > = B then B : = C + D + X
If (N = 45) THEN X : = X + 2 ELSEX : = 0
If A < = B then A : = C * D
If (A > = B) X : Y else X : = Z

⇒ Hall effect is observed in a specimen (metal or semi- conductor) when it is carrying current and is placed in a magnetic field. The resultant electric field inside the specimen is
normal to both current and magnetic field
in the same direction as current
in a direction anti parallel to magnetic field
none of the above

⇒ Fourier transform and F(jω) of a signal f(t) has the property
F(jω) = F(-jω)
F(jω) = -F(-jω)
F(jω) = F^*(jω)
F(jω) = -F^*(-jω)

⇒ In a 3 phase full converter feeding a highly inductive load, the average load current is 150 A. The peak current through thyristor is
150 A
75 A
50 A
300 A

⇒ In figure the open circuit em
15 V
1.45 V
1.475 V
1.485 V

⇒

Match the following:

	List I (Operator)		List II (Description)
A.	! =	1.	Left shift
B.	= =	2.	Right Shift
C.	< <	3.	Equal to
D.	> >	4.	Not equal to

A-1, B-2, C-3, D-4
A-2, B-3, C-4, D-1
A-4, B-1, C-3, D-2
A-4, B-3, C-1, D-2

⇒ If x = 0.1396 radians, the values of 1 - cos x and 2 sin² (x / 2) using floating point arithmetic with a 4 digit mantissa are respectively
.1000 E - 1 each
.9727 E - 2 each
.1000 E - 1 and .9727 E - 2 respectively
.9727 E - 2 and .1000 E - 1 respectively

⇒ The cut off wavelength λ_c for TE₂₀ mode for a standard rectangles waveguide is
2/a
2a
a
2a²

⇒ What binary number does second row represent?
1111001
1010101
10101010
11101010