Question is ⇒ Which of the following motors is most suitable for signalling devices and many kinds of timers ?, Options are ⇒ (A) D.C. shunt motor, (B) D.C. series motor, (C) Induction motor, (D) Reluctance motor, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following motors is most suitable for signalling devices and many kinds of timers ?, Options are ⇒ (A) D.C. shunt motor, (B) D.C. series motor, (C) Induction motor, (D) Reluctance motor, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following motors is most suitable for signalling devices and many kinds of timers ?
A.	D.C. shunt motor [Wrong Answer]
B.	D.C. series motor [Wrong Answer]
C.	Induction motor [Wrong Answer]
D.	Reluctance motor [Correct Answer]
View Answer 4 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which D.C. motor is preferred for elevators ?
Shunt motor
Series motor
Differential compoun.d motor
Cumulative compound motor

⇒ D.C. series machine has field consisting of
many number of turns of thick wire
many number of turns of thin wire
few number of turns of thick wire
few number of turns of thin wire

⇒ In hazardous area of gassy mines, material transportation is done by vehicles powered by
A.C. mains
D.C. mains
I.C. engines
batteries

⇒ If a D.C. motor is connected across the A.C. supply it will
run at normal speed
not run
run at lower Speed
burn due to heat produced in the field winding by eddy currents

⇒ A shearing machine has cyclic load consisting of intermittent light and henry loads. Which of the following D.C. motor will be suitable for this purpose?
Series motor
Shunt motor
Cumulative compound motor
Differential compound motor

⇒ Ward-Leonard system of speed control is not recommended for
very low speeds
frequent motor reversals
wide speed range
constant speed operation

⇒ If a D.C. shunt motor is working at full load and if shunt field circuit suddenly opens
this will make armature to take heavy current, possibly burning it
this will result in excessive speed, possibly destroying armature due to excessive centrifugal stresses
nothing will happen to motor
motor will come to stop

⇒ The hysteresis loss in a D.C. machine least depends on
Frequency of magnetic reversals
Maximum value of flux density
Volume and grade of iron
Rate of flow of ventilating air

⇒ By looking at which part of the motor, it can be easily confirmed that a particular motor is D.C. motor?
Frame
Shaft
Commutator
Stator

⇒ Torque developed by a D.C. motor depends upon
active length of the conductor
current flow through the conductors
number of conductors
radius of armature

⇒ A D.C. motor can be easily identified by
winding
commutator
size of conductor
yoke

⇒ A motor for punching machine is usually subjected to
no load
continuous part load
continuous full load
intermittent load

⇒ Which loss in a D.C. generator does not vary with load as well as flux density ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ Four point starter in the D.C. motor is used
to decrease the field current
to increase the field current
not to effect the current passing through Hold on coil even if any change M the field current takes place
all of the above

⇒ All motors, basically, operate on the principie of either repulsion or
induction
semi-conduction
capacitance
electro-magnetism

⇒ The speed of a motor falls from 1100 r.p.m. at no-load to 1050 r.p.m. at rated load. The speed regulation of the motor is
0.0236
0.0476
0.0677
0.0884

⇒ Which D.C. motor will be preferred for machine tools ?
Series motor
Shunt motor
Cumulative compound motor
Differential compound motor

⇒ Which of the following statement is incorrect ? If a starter is not used with large D.C. motor, it will draw a starting current which
will produce very low starting torque
will produce excessive line voltage drop
will damage the cOmmutator
is many times its full-load current

⇒ For a D.C. shunt motor if the excitation is changed
torque will remain constant
torque will change but power will remain constant
torque and power both will change
torque, power and speed, all will change

⇒ Speed control by the variation of flux, in a D.C. shunt motor, will give
constant torque drive
variable torque drive
constant power drive
variable power drive

⇒ In a motor, energy conversion would not have been possible but for the
production of opposing back e.m.f. Eb in the armature
input energy from supply
use of commutator
application of Fleming's left-hand rule

⇒ Which of the following motor has high starting torque ?
Synchronous motor
A.C. series motor
D.C. series motor
Induction motor

⇒ Which of the following motors, on removal of load, will run at the highest speed ?
Shunt motor
Series motor
Differential compound
Cumulative compound

⇒ In which of the following applications D.C. series motor is invariably tried?
Starter for a car
Drive for a water pump
Fan motor
Motor operation in A.C. or D.C.

⇒ In a manual shunt motor starter
over load relay is connected in series and no volt relay in parallel with the load
over load relay is connected in parallel and no volt relay in series with the load
over load relay and no volt relay are both connected in series with the load
over load relay and no volt relay are both connected in parallel with the load

⇒ If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will
increase
decrease
remain same
become zero

⇒ Which one of the following is not necessarily the advantage of D.C. motors over A.C. motors ?
Low cost
Wide speed range
Stability
High starting torque

⇒ In D.C. shunt motors as load is reduced
the speed will increase abruptly
the speed will increase in proportion to reduction in load
the speed will remain almost constant
the speed will reduce

⇒ As there is no back e.m.f. at the instant of starting, a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit
a resistance is connected in series with armature
a resistance is connected parallel to the armature
armature is temporarily open circuited
a high value resistor is connected across the field winding

⇒ Which D.C. motor will be suitable alongwith flywheel for intermittent light and heavy loads?
Series motor
Shunt motor
Cumulatively compounded motor
Differentially compounded motor