Question is ⇒ The speed of a motor falls from 1100 r.p.m. at no-load to 1050 r.p.m. at rated load. The speed regulation of the motor is, Options are ⇒ (A) 0.0236, (B) 0.0476, (C) 0.0677, (D) 0.0884, (E) , Leave your comments or Download question paper.

Question is ⇒ The speed of a motor falls from 1100 r.p.m. at no-load to 1050 r.p.m. at rated load. The speed regulation of the motor is, Options are ⇒ (A) 0.0236, (B) 0.0476, (C) 0.0677, (D) 0.0884, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	The speed of a motor falls from 1100 r.p.m. at no-load to 1050 r.p.m. at rated load. The speed regulation of the motor is
A.	0.0236 [Wrong Answer]
B.	0.0476 [Correct Answer]
C.	0.0677 [Wrong Answer]
D.	0.0884 [Wrong Answer]
View Answer 3 -4 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following motors is most suitable for signalling devices and many kinds of timers ?
D.C. shunt motor
D.C. series motor
Induction motor
Reluctance motor

⇒ Regenerative braking on shunt motors is used when
the load is variable
the load is constantly decreasing
the load acts as a braking force
the load has overhauling characteristics.

⇒ In hazardous area of gassy mines, material transportation is done by vehicles powered by
A.C. mains
D.C. mains
I.C. engines
batteries

⇒ Which of the following can be used to control the speed of a D.C. motor ?
Thermistor
Thyristor
Thyratron
Transistor

⇒ The maximum end-play of a motor is about
10 mm
6 mm
2 mm
0.4 mm

⇒ Four point starter in the D.C. motor is used
to decrease the field current
to increase the field current
not to effect the current passing through Hold on coil even if any change M the field current takes place
all of the above

⇒ The current drawn by the armature of D.C. motor is directly proportional to
the torque required
the speed of the motor
the voltage across the terminals
none of the above

⇒ When the armature of a D.C. motor rotates, e.m.f. induced is
self-induced e.m.f.
mutually induced e.m.f.
back e.m.f.
none of the above

⇒ Which D.C. motor has got maximum self relieving property ?
Series motor
Shunt motor
Cumulatively compounded motor
Differentially compounded motor

⇒ The generated e.m.f. and the current are in the opposite direction in case of
d.c. generators
d.c. motors
both (a) and (b)
none of the above

⇒ D.C. generators are normally designed for maximum efficiency around
full-load
rated r.p.m.
rated voltage
all of the above

⇒ In case of a shunt motor if the supply voltage is increased by 10%, which of the following will decrease ?
full load current
full load speed
starting torque
none of the above

⇒ Which of the following application requires high starting torque ?
Lathe machine
Centrifugal pump
Locomotive
Air blower

⇒ A D.C. shunt motor is rotating in clockwise direction as viewed from one end. The polarity of connection of the armature and field winding are reversed simultaneously. The motor will
rotate in clockwise direction
rotate in anti-clockwise direction
will not rotate at all
gain excessively high speed

⇒ A 230 V D.C. shlint motor takes 32 A at full load. The back e.m.f. on full load, if the resistance of motor armature and shunt field windings are 0.2 Ω and 115 Ω respectively, will be
210 V
215 V
220 V
224 V

⇒ One D.C. motor drives another D.C. motor. The second D.C. motor when excited and driven
runs as a generator
does not run as a generator
also runs as a motor
comes to stop after sometime

⇒ Which of the following tests will be suitable for testing two similar D.C. series motors of large capacity ?
Swinburne's test
Hopkinson's test
Field test
Brake test

⇒ Which of the following methods is most ecoriomical fol. finding the no-load losses of a large b.C. shunt motor ?
Retardation test
Swinburne's test
Hopkinson's test
none of the above

⇒ Which of the following motor is preferred for operation in highly explosive atmosphere ?
Series motor
Shunt motor
Air motor
Battery operated motor

⇒ In electric motors carbon brushes are used to
provide a path for flow of current
prevent sparking during commutation
prevent overheating of armature windings
brush off carbon deposits on the commutator

⇒ Hopkinson's test is conducted at
no load
part load
low load
full load

⇒ As the load is increased the speed of D.C. shunt motor will
reduce slightly
increase slightly
increase proportionately -
remains unchanged

⇒ Which of the following methods of braking is used in rolling mills ?
Dynamic braking
Plugging
Regenerative braking
Mechanical brakes

⇒ The type of D.C. motor used for shears and punches is
shunt motor.
series motor
differential compound D.C. motor
cumulative compound D.C. motor

⇒ If the no-voltage release of a D.C. motor starter fails to work on resumption of supply after a break, the motor will
not start automatically
start automatically without trouble
get damaged
develop very low torque

⇒ Which of the following loss in a D.C. generator varies significantly with the load current ?
Field copper loss
Windage loss
Armature copper loss
None of the above

⇒ Torque developed by a D.C. motor depends upon
active length of the conductor
current flow through the conductors
number of conductors
radius of armature

⇒ D.C. motor is to drive a load which has certain minimum value for most of the time and some peak value for short duration. We will select the
series motor
shunt motor
compound motor
any of the above

⇒ For a D.C. shunt motor if the excitation is changed
torque will remain constant
torque will change but power will remain constant
torque and power both will change
torque, power and speed, all will change

⇒ Compensating winding in a D.C. machine is placed
on yoke in the pole faces
on yoke in the interpolar gap
on armature
none of the above