Question is ⇒ in a D.C. generator, the iron losses mainly take place in, Options are ⇒ (A) yoke, (B) commutator, (C) armature conductors, (D) armature rotor, (E) , Leave your comments or Download question paper.

Question is ⇒ in a D.C. generator, the iron losses mainly take place in, Options are ⇒ (A) yoke, (B) commutator, (C) armature conductors, (D) armature rotor, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	in a D.C. generator, the iron losses mainly take place in
A.	yoke [Wrong Answer]
B.	commutator [Wrong Answer]
C.	armature conductors [Wrong Answer]
D.	armature rotor [Correct Answer]
View Answer 10 -13 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ D.C. series machine has field consisting of
many number of turns of thick wire
many number of turns of thin wire
few number of turns of thick wire
few number of turns of thin wire

⇒ For constant torque drive which speed control method is preferred ?
Field control
Armature voltage control
Shunt armature control
Mechanical loading system

⇒ A wide and very sensitive speed control is usually required in case of
elevators
steel rolling mills
colliery winders
all of the above

⇒ If a D.C. motor is to be selected for conveyors, which motor would be preferred ?
Series motor
Shunt motor
Differentially compound motor
Cumulative compound motor

⇒ Which of the following tests can be used to determine no-load losses in a D.C. shunt motor ?
Running down test
Swinburne's test
Field test
Brake test

⇒ For the same H.P. rating and full load speed, following motor has poor starting torque
shunt
series
differentially compounded
cumulatively compounded

⇒ For which types of D.C. motor, dynamic braking is generally used ?
Shunt motors
Series motors
Compound motors
All of the above

⇒ In case of a shunt motor if the supply voltage is increased by 10%, which of the following will decrease ?
full load current
full load speed
starting torque
none of the above

⇒ During rheostat braking of D.C. series motors
motor is run as a generator
motor is reversed in direction
motor is run at reduced speed

⇒ Flywheel is used with D.C. compound motor to reduce the peak demand by the motor, compound motor will have to be
level compounded
under compounded
cumulatively compounded
differentially compounded

⇒ What will happen if supply terminals of D.C. shunt motor are interchanged ?
The direction of rotation will reverse
Motor will stop
Motor will run at speed lower than the normal speed in the same direction
Motor will run at its normal speed in the same direction as it was running

⇒ Which method of braking is generally used in elevators ?
Plugging
Regenerative braking
Rheostatic braking
None of the above

⇒ As the load is increased the speed of D.C. shunt motor will
reduce slightly
increase slightly
increase proportionately -
remains unchanged

⇒ Which of the following can be used to control the speed of a D.C. motor ?
Thermistor
Thyristor
Thyratron
Transistor

⇒ In variable speed motor
a stronger commutating field is needed at low speed than at high speed
a weaker commutating field is needed at low speed than at higt speed
same commutating field is needed at low speed than at high speed
none of the above is correct

⇒ In a D.C. generator, the iron losses mainly take place in
yoke
commutator
armature conductors
armature rotor

⇒ For starting a D.C. motor a starter is required because
it limits the speed of the motor
it limits the starting current to a safe value
it starts the motor
none of the above

⇒ All motors, basically, operate on the principie of either repulsion or
induction
semi-conduction
capacitance
electro-magnetism

⇒ Sparking at the commutator of a D.C. motor may result in
damage to commutator segments
damage to commutator insulation
increased power consumption
all of the above

⇒ The use of armature divertor in the rheostatic method of speed control for a D.C. shunt motor makes the method
less expensive
less wasteful
suitable for rapidly changing loads
unsuitable for changing loads

⇒ In regenerative braking
motor energy is dissipai.ed as heat
motor energy is dissipated in armature heating
motor energy is dissipated in windage losses
motor is rnade to run as a generator

⇒ Four point starter in the D.C. motor is used
to decrease the field current
to increase the field current
not to effect the current passing through Hold on coil even if any change M the field current takes place
all of the above

⇒ Which of the following can be used for controlling the speed of a D.C. motor ?
Thermistor
Transistor
Thyratron
Thyristor

⇒ In an overloaded motor main danger arises due to
winding getting overheated
busbars getting heated
starter getting damaged
bearings getting overheated

⇒ Which of the following law/rule can he used to determine the direction of rotation of D.C. motor ?
Lenz's law
Faraday's law
Coloumb's law
Fleming's left-hand rule

⇒ In the D.C. motor the iron losses occur in
the field
the armature
the brushes
the commutator

⇒ In which of the following tests only one motor is required ?
Brake test
Hopkinson's test
Field's test
Swinburne's test

⇒ During rheostatic braking the braking torque is proportional to
speed
(speed)²
(speed)^-1
(speed)^-2

⇒ D.C. motor is to a drive a load which is almost nil for certain part of the load cycle and peak value for short duration. We will select this
series motor
shunt motor
compound motor
any of the above

⇒ No-load speed of which of the following motor will be highest ?
Shunt motor
Series motor
Cumulative compound motor
Differentiate compound motor