Question is ⇒ To get the speed of D.C. motor below the normal without wastage of electrical energy ____ is used., Options are ⇒ (A) Ward Leonard control, (B) rheostatic control, (C) any of the above method, (D) none of the above method, (E) , Leave your comments or Download question paper.

Question is ⇒ To get the speed of D.C. motor below the normal without wastage of electrical energy ____ is used., Options are ⇒ (A) Ward Leonard control, (B) rheostatic control, (C) any of the above method, (D) none of the above method, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	To get the speed of D.C. motor below the normal without wastage of electrical energy ____ is used.
A.	Ward Leonard control [Correct Answer]
B.	rheostatic control [Wrong Answer]
C.	any of the above method [Wrong Answer]
D.	none of the above method [Wrong Answer]
View Answer 5 -3 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A three point starter is considered suitable for
shunt motors
shunt as well as compound motors
shunt, compound and series motors
all D.C. motors

⇒ If a D.C. motor is to be selected for conveyors, which motor would be preferred ?
Series motor
Shunt motor
Differentially compound motor
Cumulative compound motor

⇒ Which of the following motor is preferred for operation in highly explosive atmosphere ?
Series motor
Shunt motor
Air motor
Battery operated motor

⇒ The simplest form of a motor controller is
relay
toggle switch
drum switch
magnetic switch

⇒ Usually wide and sensitive speed control is desired in case of
centrifugal pumps
elevators
steel rolling mills
colliery winders

⇒ As there is no back e.m.f. at the instant of starting, a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit
a resistance is connected in series with armature
a resistance is connected parallel to the armature
armature is temporarily open circuited
a high value resistor is connected across the field winding

⇒ The purpose of retardation test on D.C. shunt machines is to find out
stray losses
eddy current losses
field copper losses
windage losses

⇒ A brake test on D.C. motors is usually restricted to
small horse power motors
variable speed motors
high speed motors
open frame type motors.

⇒ No-load speed of which of the following motor will be highest ?
Shunt motor
Series motor
Cumulative compound motor
Differentiate compound motor

⇒ The armature torque of the D.C. shunt motor is proportional to
field flux only
armature current only
both (a) and (b)
none of the above

⇒ Which of the following is not necessarily the advantage of D.C. motors over A.C. motors ?
Better speed control
Low cost
High starting torque
Wide speed range

⇒ The ratio of starting torque to fullload torque is least in case of
series motors
shunt motors
compound motors
none of the above

⇒ In a D.C. motor, the ratio Eb/Va indicates
running torque of the motor
starting torque of the motor
efficiency of the motor
speed regulation of the motor

⇒ The speed of a D.C. motor can be varied by varying
field current
applied voltage
resistance in series with armature
any of the above

⇒ The speed of a series motor at no load is
infinity
4000 r.p.m.
2000 r.p.m.
1000 r.p.m.

⇒ When the electric train is moving down a hill the D.C. motor act as
D.C. series generator
D.C. shunt generator
D.C. shunt motor
D.C. series motor

⇒ Which loss in a D.C. generator does not vary with load as well as flux density ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ The function of a field regulator for compound motors is to
control the flux
limit the armature current
demagnetise the field partially
none of the above

⇒ Between Field's test and Hopkinson's test the main common thing is that both
use negligible power
are regenerative tests
need two similar mechanicallycoupled motors
need two electrically coupled series motors

⇒ In a D.C. generator, the iron losses mainly take place in
yoke
commutator
armature conductors
armature rotor

⇒ One D.C. motor drives another D.C. motor. The second D.C. motor when excited and driven
runs as a generator
does not run as a generator
also runs as a motor
comes to stop after sometime

⇒ In regenerative braking
motor energy is dissipai.ed as heat
motor energy is dissipated in armature heating
motor energy is dissipated in windage losses
motor is rnade to run as a generator

⇒ To get the speed of D.C. motor below the normal without wastage of electrical energy ____ is used.
Ward Leonard control
rheostatic control
any of the above method
none of the above method

⇒ Which loss in a D.C. generator varies with load ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ What will happen if supply terminals of D.C. shunt motor are interchanged ?
The direction of rotation will reverse
Motor will stop
Motor will run at speed lower than the normal speed in the same direction
Motor will run at its normal speed in the same direction as it was running

⇒ Which method of braking is generally used in elevators ?
Plugging
Regenerative braking
Rheostatic braking
None of the above

⇒ The rated speed of a given D.C. shunt motor is 900 r.p.m. To run this machine at 1000 r.p.m., which of the following speed control scheme will be used ?
Ward-leonard control
Armature current resistance control
Field resistance control
None of the above

⇒ Which D.C. motor has got maximum self relieving property ?
Series motor
Shunt motor
Cumulatively compounded motor
Differentially compounded motor

⇒ Which of the following tests will be suitable for testing two similar D.C. series motors of large capacity ?
Swinburne's test
Hopkinson's test
Field test
Brake test

⇒ If a D.C. motor designed for 40°C ambient temperature is to be used for 50°C ambient temperature, then the motor
of lower H.P. should be selected
of higher H.P. should be selected
can be used for 50°C ambient temperature also
is to be derated by a factor recommended by manufacturer and select the next higher H.P. motor