Question is ⇒ Specific resistance of silver is about, Options are ⇒ (A) 0.16 x 10-8 Ω-m, (B) 1.64 x 10-8 Ω-m, (C) 16 x 10-8 Ω-m, (D) 164 x 10-8 Ω-m, (E) , Leave your comments or Download question paper.

Question is ⇒ Specific resistance of silver is about, Options are ⇒ (A) 0.16 x 10-8 Ω-m, (B) 1.64 x 10-8 Ω-m, (C) 16 x 10-8 Ω-m, (D) 164 x 10-8 Ω-m, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Specific resistance of silver is about
A.	0.16 x 10^-8 Ω-m [Wrong Answer]
B.	1.64 x 10^-8 Ω-m [Correct Answer]
C.	16 x 10^-8 Ω-m [Wrong Answer]
D.	164 x 10^-8 Ω-m [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In TV systems, equalising pulses are sent during
horizontal blanking
vertical blanking
serrations
horizontal retrace

⇒ The shape of torque-speed curve of a two phase servo- motor mostly depends on
ratio of rotor reactance to rotor resistance
ratio of stator reactance to rotor resistance
ratio of rotor reactance to rotor resistance and also the ratio of stator reactance to stator resistance
magnitude of stator voltages

⇒ India's first three-axis stabilised geostationary communication satellite is
Rohini
Aryabhatta
Apple
Bhaskara

⇒ A quiescent state of a transistor implies
zero bias
no output
no distortion
no input signal

⇒ Wave A = 100 sin ωt and wave B = 100 cos ωt. Then
rms values of the two waves are equal
rms values of A is more than that of B
rms values of A is less than that of B
rms values of the two waves may or may not be equal

⇒ What is the major cause of creeping in an energy-meter?
Over compensation for friction
Mechanical vibrations
Excessive voltage across the potential coil
Stray magnetic fields

⇒ If sequence currents I_a1 = 2 ∠- 90°, I_a2 = 0.2 ∠ 90° and I_a3 = 1.8 ∠ 90°, I_a =
0
1
4
8

⇒ A signal occupies a band 5 kHz to 10 kHz. For proper error free reconstruction at what rate it should be sampled?
10 kHz
20 kHz
5 kHz
(10 + 5) x 2 kHz

⇒ If N bits are lumped together to get an N-bit symbol, the possible number of symbols is
2^N
2^{N - 1}
2^{N - 2}
2^{N - 4}

⇒ An electromechanical device which actuates a train of step angular movements in response to a train of input pulses on one to one basis is
synchro control transformer
LVDT
stepper motor
tacho generator

⇒ In sinusoidal PWM for inverters the width of different pulses are not the same.
TRUE
FALSE

⇒ In an impedance smith chart, a clockwise movement along a constant resistance circle gives rise to
decrease in the value of reactance
an increase in the value of reactance
no change in the reactance value
no change in the impedance value

⇒ The materials having low retentivity are suitable for making
temporary smagnets
weak magnets
permanent magnets
both temporary and permanent magnets

⇒ Zener breakdown occurs
due to rapture of covalent band
mostly in germanium junctions
in lightly doped junctions
due to thermally generated minority carriers

⇒

Assertion (A): Different symbols are used for different gates

Reason (R): IEEE symbols are the same as traditional symbols for gates.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ High frequency waves are
absorbed by F₂ layer
affected by solar cycle
reflected by D layer
none of the above

⇒ The figures shows the symbo
p channel depletion MOSFET
p channel enhancement MOSFET
complementary MOSFET
p channel JFET

⇒ For 200V r.m.s. value triangular wave, the peak voltage will be
200 V
222 V
280 V
346 V

⇒ When the ac base voltage in a CE amplifier circuit is too high, the ac emitter current is
zero
constant
alternating
distorted

⇒ In a 7 segment LED display, the minimum number of segments is activated when the input decimal number is
0
1
2
3

⇒ A MASER is a
low noise device
high noise device
medium noise device
may be either high or medium noise device

⇒ The first dominant pole encountered in the frequency response of a compensated op-amp is approximately at
5 Hz
10 kHz
1 MHz
100 MHz

⇒ Which of these statements is correct?
Ridge guide is essentially a form of capacitively loaded guide.
Ridge guide is essentially a form of inductively loaded guide.
Ridge guide is essentially a form of resistively loaded guide.
Ridge guide has higher power handling capacity than rectangular waveguide.

⇒ Which capacitor-store higher amount of energy?
Air capacitor
Paper capacitor
Mica capacitor
Plastic film capacitor

⇒ Digital technologies being used now-a-days are
DTL and EMOS
TTL, ECL, CMOS and RTL
TTL, ECL and CMOS
TTL, ECL. CMOS and DTL

⇒ When the emitter current of a transistor is changed by 1 mA, its collector current changes by 0.990 mA. The common base short circuit current gain a for the transistor is
0.99
1.01
1.001
0.99

⇒ Giga watt is equal to
10¹² W
10⁹ W
10⁶ W
10³ W

⇒ The input resistance R, of an ideal voltage amplifier is __________ and that of a current amplifier is __________ .
zero, zero
infinite, infinite
zero, infinite
infinite, zero

⇒ The frequency range of 300 kHz to 3000 kHz is known as
low frequency
medium frequency
high frequency
very high frequency

⇒ The op-amp used in nonlinear mode is
integrators
active filters
Schmitt triggers
instrumentation amplifiers