Question is ⇒ In a single phase full wave controlled rectifier using centre tap transformer, the voltage across each half of secondary is Vm sin ωt. The peak inverse voltage is, Options are ⇒ (A) 2 Vm, (B) Vm, (C) 0.5 Vm, (D) 0.25 Vm, (E) , Leave your comments or Download question paper.

Question is ⇒ In a single phase full wave controlled rectifier using centre tap transformer, the voltage across each half of secondary is Vm sin ωt. The peak inverse voltage is, Options are ⇒ (A) 2 Vm, (B) Vm, (C) 0.5 Vm, (D) 0.25 Vm, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In a single phase full wave controlled rectifier using centre tap transformer, the voltage across each half of secondary is V_m sin ωt. The peak inverse voltage is
A.	2 V_m [Correct Answer]
B.	V_m [Wrong Answer]
C.	0.5 V_m [Wrong Answer]
D.	0.25 V_m [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The spectrum of the white noise and an impulse function is similar in following aspects
both have similar magnitude spectrum
both have similar magnitude and Phase spectrum
no relation
similar phase spectrum

⇒ In a centre tap full wave rectifier, 50 V is the peak voltage between the centre tap and one of the ends of the secondary. The maximum voltage across the reverse biased diode will be
100 V
72 V
50 V
38 V

⇒ The basic amplifier in Weinbridge oscillator consists of
CE stage followed by CE
CE stage followed by CB
CB stage followed by CE
CC stage followed by CE

⇒ A voltage doubler circuit uses
two diodes
two capacitors
two diodes and two capacitors
none of the above

⇒ The address to which a software or hardware restart branches is known as
Vector location
SID
SOD
TRAP

⇒ Z transform is a non-linear operation.
TRUE
FALSE

⇒ Maxterm designation for A + B + C is
M₀
M₁
M₃
M₄

⇒ A resistance strain gauge has a resistance of about
100 Ω
25 Ω
10 Ω
1 Ω

⇒ In a forward biased p-n junction current enters p material as hole current and leaves n material as electron current of the same magnitude.
TRUE
FALSE

⇒ A diode peak reading VTVM and thermocouple meter are connected across output of an amplitude modulated circuit. In the absence of modulation both meters read 10 V. When sinusoidal AM is applied, VTVM reads 15V The reading of thermocouple meter will be
10 V
12.5 V
14.1 V
15 V

⇒ Unit doublet is the Laplace inverse of __________ .
1/s
s²
s
none of these

⇒ In a colour TV receiver, the function of comb filter is
to pass only the clusters of monochrome signal energy while blocking chrome signals
to pass only chrome signals and block monochrome signals
to block both monochrome and chrome signals
none of the above

⇒ In a pneumatic bellows
the input surface, output surface and side walls are corrugated
the input surface and output surface are flat but the side walls are corrugated
the input surface and side walls are flat but the output surface is corrugated
the input surface and output surface are corrugated but the side walls are flat

⇒ For a BJT a = 0.98, then β =
0.02
0.5
4.9
48

⇒ In a JFET avalanche breakdown occurs when V_DS = 22 V and V_GS = 0. If V_GS = -1 V, the avalanche breakdown will occur at
V_DS = 22 V
V_DS more than 22 V
V_DS equal to or more than 22 V
V_DS less than 22 V

⇒ Which of them has 10 inputs and 4 outputs?
Decimal to BCD encoder
BCD to decimal decoder
Octal to binary encoder
All encoders

⇒ The current flowing in a certain P-N junction at room temperature is 2 x 10^-7 Amp. When a large reverse biased voltage is applied. Calculate the current flowing when 0.1 volts is applied.
9 μA
10 μA
2 μA
4 μA

⇒ The residual resistivity of a binary alloy at 0°K is
the sum of the residual resistivities of the component metals
the difference of the residual resistivities of the component metals
the product of the residual resistivities of the component metals
depend on the concentration of the minor component in the alloy

⇒ To realize the full power of 8086 the pin of 8086 connected to ground is
DEN
ALE
INTR
MN / MX

⇒ At high frequencies the output circuit of transistor amplifier reduces to
a lead network
a lag network
either (a) or (b)
neither (a) nor (b)

⇒ In a ballistic galvanometer, a charge of 100 μC gives a first swing of 25°. The charge required to cause first swing of 50° is
200 μC
400 μC
50 μC
25 μC

⇒ To prevent a DC return between source and load, it is necessary to use
resistor between source and load
inductor between source and load
capacitor between source and load
either (a) or (b)

⇒ Which of the following codes is based on BCD format?
EBCDIC
ASCII
Hollerith
both (a) and (b)

⇒ In telecast
video and audio signals are frequency modulated
video signals are frequency modulated but audio signals are amplitude modulated
both audio and video signals are amplitude modulated
video signals are amplitude modulated and audio signals are frequency modulated

⇒ IC (instruction cycle), FC (fetch cycle) and EC (executive cycle) are related as
IC = FC - EC
IC = FC + EC
IC = FC + 2EC
EC = IC + EC

⇒ The specified maximum junction temperature of thyristors is about
50°C
80°C
120°C
200°C

⇒ In control systems the magnitude of error voltage
is very small
is very large
neither small nor large
may be any value from 0 to 50 V

⇒ In the circuit shown, the device connected to Y5 can have address in the r
2000 - 20FF
2D00 - 2DFF
2E00 - 2EFF
FD00 - FDFF

⇒ The units of transistor h parameters h₁₁ and h₂₂ are the same.
TRUE
FALSE

⇒ When a circuit is excited by ac sinusoidal source, the admittance is obtained by letting s = jω in Y(s).
TRUE
FALSE