Question is ⇒ Contour lines of different elevations can unite to form one line, only in the case of., Options are ⇒ (A) a vertical cliff, (B) a saddle, (C) a water shed line, (D) a hill top., (E) , Leave your comments or Download question paper.

Question is ⇒ Contour lines of different elevations can unite to form one line, only in the case of., Options are ⇒ (A) a vertical cliff, (B) a saddle, (C) a water shed line, (D) a hill top., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Contour lines of different elevations can unite to form one line, only in the case of.
A.	a vertical cliff [Correct Answer]
B.	a saddle [Wrong Answer]
C.	a water shed line [Wrong Answer]
D.	a hill top. [Wrong Answer]
View Answer 24 -3 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Closed contours of decreasing values towards their centre, represent.
a hill
a depression
a saddle or pass
a river bed.

⇒ A horizontal angle which a line makes with the true meridian through one of the extremities of the line is called
Bearing
True bearing
Imaginary bearing
Maimetic bearing

⇒ There are two stations A and B. Which of the following statements is correct :
the fore bearing of AB is AB
the back bearing of AB is BA
the fore and back bearings of AB differ by 180Â°
all the above.

⇒ The accuracy of fix obtained by solving a two point problem is
Good
Fairly accurate
Not reliable
None of these

⇒ Perpendicular offset from a tangent to the junction of a transition curve and circular curve is equal to.
shift
twice the shift
thrice the shift
four times the shift.

⇒ Metric chains are generally available in.
10 m and 20 m length
15 m and 20 m length
20 m and 30 m length
25 m and 100 m length

⇒ In a lemniscate curve the ratio of the angle between the tangent at the end of the polar ray and the straight, and the angle between the polar ray and the straight, is.
2
3
4
3/2

⇒ The 'point of curve' of a simple circular curve, is.
point of tangency
point of commencement
point of intersection
mid-point of the curve

⇒ In direct method of contouring, the process of locating or identifying points lying on a contour is called
ranging
centring
horizontal control
vertical control

⇒ The first reading from a level station is.
foresight
intermediate sight
back-sight
any sight.

⇒ Which of the following methods of offsets involves less measurement on the ground?
method of perpendicular offsets
method of oblique offsets
method of ties
all involve equal measurement on the ground

⇒ The constant vertical distance between two adjacent contours, is called.
horizontal interval
horizontal equivalent
vertical equivalent
contour interval

⇒ As per Indian standard, the length of one link in 30 metre chain should be
30 cm
20 cm
40 cm
10 cm

⇒ When the meridian of a plane changes with time, then this meridian will be
Arbitrary
Magnetic
True
Grid

⇒ In geodetic surveys higher accuracy is achieved, if.
curvature of the earth surface is ignored
curvature of the earth surface is taken into account
angles between the curved lines are treated as plane angles
none of these.

⇒ Which one of the following mistakes/errors may be cumulative + or - :
bad ranging
bad straightening
erroneous length of chain
sag.

⇒ The combined effect of curvature and refraction over a distance L kilometres is.
67.2 L2 mm
76.3 L2 mm
64.5 L2 mm
none of these.

⇒ Surveys which are carried out to provide a national grid of control for preparation of accurate maps of large areas, are known.
plane surveys
geodetic surveys
geographical surveys
topographical surveys.

⇒ Theodolite is an instrument used for
tightening the capstan-headed nuts of level tube
measurement of horizontal angles only
measurement of vertical angles only
measurement of both horizontal and vertical angles

⇒ Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of offset should be limited to.
14.14
28.28 m
200 m
none of these.

⇒ The smaller horizontal angle between the true meridian and a survey line, is known.
declination
bearing
azimuth
dip.

⇒ The length of a traverse leg may be obtained by multiplying the latitude and.
secant of its reduced bearing
sine of its reduced bearing
cosine of its reduced bearing
tangent of its reduced bearing.

⇒ The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as.
Plane alidade
telescopic alidade
clinometer
tacheometer.

⇒ The difference in the lengths of an arc and its subtended chord on the earth surface for a distance of 18.2 km, is only.
1 cm
5 cm
10 cm
100 cm.

⇒ Detailed plotting is generally done by
radiation
traversing
resection
all of the above

⇒ In horizontal angles, the error due to imperfect levelling of the plate bubble is.
large when sights are nearly level
large for long sights
less for steeply inclined sights
large for steeply inclined sights.

⇒ Optical reading instruments.
the vertical circle is usually continuous from 0Â° to 359Â°
the readings increase when the telescope is elevated in the face left position
the readings decrease when the telescope is elevated in the face right position
all the above.

⇒ Agate cap is fitted with a
cross staff
level
chain
prismatic compass

⇒ The total change in level along the line is equal to total back sights.
minus total fore sights
the total rises minus total falls
the reduced level of last point minus reduced level of the first point
all the above.

⇒ Flint glass.
has slightly the greater refracting power than crown glass
has roughly double refracting power than that of crown
and crown glass proportions yield the required focal length and neutralise the dispersion produced by the convex lens at the emergence from the concave
all the above.