Question is ⇒ In chain surveying, perpendiculars to the chain line, are set out by., Options are ⇒ (A) a theodolite, (B) a prismatic compass, (C) a level, (D) an optical square, (E) , Leave your comments or Download question paper.

Question is ⇒ In chain surveying, perpendiculars to the chain line, are set out by., Options are ⇒ (A) a theodolite, (B) a prismatic compass, (C) a level, (D) an optical square, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	In chain surveying, perpendiculars to the chain line, are set out by.
A.	a theodolite [Wrong Answer]
B.	a prismatic compass [Wrong Answer]
C.	a level [Wrong Answer]
D.	an optical square [Correct Answer]
View Answer 27 -6 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The longitudinal section of the surface of bubble tube is.
straight
circular
parabolic
elliptic.

⇒ Cross-staff is used for.
setting out right angles
measuring contour gradient
taking levels
measuring distances

⇒ The method generally preferred to for contouring an undulating area, is.
chain surveying
plane table surveying
tacheometrical surveying
compass surveying.

⇒ The surface of zero elevation around the earth, which is slightly irregular and curved, is known as.
mean sea level
geoid surface
level surface
horizontal surface.

⇒ At magnetic poles the dip of magnetic needle is
0°
45°
90°
120°

⇒ Negative errors are caused in chain, when its length is
More than the standard length
Iess than the standard length
Equal to the standard length
Any of the above

⇒ Off sets are
Chain lines out of alignment
Small measurements from chain line
Measurements taken in chain surveying
None of the above

⇒ The horizontal angle between true meridian and magnetic meridian, is known.
bearing
magnetic declination
dip
convergence.

⇒ In an adjusted level, when the bubble is central, the axis of the bubble tube becomes parallel to.
line of sight
line of collimation
axis of the telescope
None of these.

⇒ From any point on the surface with a given inclination.
only one contour gradient is possible
two contour gradients are possible
indefinite contour gradients are possible
all the above.

⇒ The type of surveying which requires least office work is
tacheomefry
trigonometrical levelling
plane table surveying
theodolite surveying

⇒ If the reduced bearing of a line AB is N60°W and length is 100 m, then the latitude and departure respectively of the line AB will be
+50 m, +86.6 m
+86.6 m, -50 m
+50m, -86.6 m
+70.7 m,-50 m

⇒ The process of turning the telescope about the vertical axis in horizontal plane is known as
transiting
reversing
plunging
swinging

⇒ In case of a direct vernier scale.
graduations increase in opposite direction in which graduations of the main scale increase
smallest division is longer than smallest division of the main scale
graduations increase in the same direction in which graduations of the main scale increase
none of these.

⇒ In levelling operation,
The first sight on any change point is a back sight
The second sight on any change point is a fore sight
The line commences with a fore sight and closes with a back sight
The line commences with a back sight and closes with a foresight.

⇒ The co-ordinate of a point measured perpendicular to the parallel, is called.
total latitude
meridian distance
total departure
consecutive co-ordinate.

⇒ Which of the following introduces an error of about 1 in 1000 if 20 m chain is used.
length of chain 20 mm wrong
one end of the chain 0.9 m off the line
one end of chain 0.9 m higher than the other
all the above.

⇒ The most reliable method of plotting a theodolite traverse, is.
by consecutive co-ordinates of each station
by independent co-ordinates of each station
by plotting included angles and scaling off each traverse leg
by the tangent method of plotting.

⇒ Tadia techeometry was discovered by James Watt in the year.
1670
1770
1870
1900.

⇒ The error due to eccentricity of inner and outer axes can be eliminated by
reading both verniers and taking the mean of the two
taking both face observations and taking the mean of the two
double sighting
taking mean of several readings distributed over different portions of the graduated circle

⇒ Which of the following errors can be eliminated by taking mean of bot face observations ?
error due to imperfect graduations
error due to eccentricity of verniers
error due to imperfect adjustment of plate levels
error due to line of collimation not being perpendicular to horizontal axis

⇒ As per Indian Standard the total number of links in a 30 metre chain should be
100
150
300
75

⇒ Generally while chaining the arrow which accompany with one chain must be
2 Nos
5 Nos
10 Nos
12 Nos

⇒ For a well-conditioned triangle, no angle should be less than
20°
30°
45°
60°

⇒ Perpendicularity of an offset may be judged by eye, if the length of the offset is.
5 m
10 m
15 m
20 m

⇒ If the horizontal distance between the staff point and the point of observation is d, then the error due to curvature of earth is proportional to
d
1/d
d2
1/d2

⇒ Which of the following is not used in measuring perpendicular offsets ?
line ranger
steel tape
optical square
cross staff

⇒ The following sights are taken on a "turning point"
foresight only
backsight only
foresight and backsight
foresight and intermediate sight

⇒ In a constant level tube, size of the bubble remains constant because upper wall is.
of relatively larger radius
of relatively smaller radius
flat
convex downwards.

⇒ An error under the same conditions always of the same size and sign is called as
Uniform error
Systematic error
Cumulative error
Any of (B) and (C) above