Question is ⇒ To avoid large centering error with very short legs, observations are generally made., Options are ⇒ (A) to chain pins, (B) by using optical system for centering the theodolite, (C) to a target fixed on theodolite tripod on which theodolite may be fitted easily, (D) all the above., (E) , Leave your comments or Download question paper.

Question is ⇒ To avoid large centering error with very short legs, observations are generally made., Options are ⇒ (A) to chain pins, (B) by using optical system for centering the theodolite, (C) to a target fixed on theodolite tripod on which theodolite may be fitted easily, (D) all the above., (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	To avoid large centering error with very short legs, observations are generally made.
A.	to chain pins [Wrong Answer]
B.	by using optical system for centering the theodolite [Wrong Answer]
C.	to a target fixed on theodolite tripod on which theodolite may be fitted easily [Correct Answer]
D.	all the above. [Wrong Answer]
View Answer 20 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ If the focal length of the object glass is 25 cm and the distance from object glass to the trunnion axis is 15 cm, the additive constant is
0.1
0.4
0.6
1.33

⇒ The conventional sign shown in below figure represents a

road bridge
railway bridge
canal bridge
aquaduct.

⇒ The angle between two plane mirrors of an optical square should be
30°
45°
60°
90°

⇒ Direct method of contouring is
a quick method
adopted for large surveys only
most accurate method
suitable for hilly terrains

⇒ The two point or three point problems are methods of
Orientation
Resection
Traversing
(A) and (B) above

⇒ The co-ordinate of a point measured perpendicular to the parallel, is called.
total latitude
meridian distance
total departure
consecutive co-ordinate.

⇒ Generally while chaining the arrow which accompany with one chain must be
2 Nos
5 Nos
10 Nos
12 Nos

⇒ Accuracy of 'fix' by two point problem, is.
bad
good
not reliable
unique.

⇒ If the declination of the needle is 10° W.
each of the whole circle reckoning has to be micros by 10Â°
in the quadrantal method, the correction is positive in the 1st and 3rd quadrants
in the quadrantal method, the corrections is negative in 2nd and 4th quadrants
all the above.

⇒ Which of the following is not the function of levelling head ?
to support the main part of the instrument
to attach the theodolite to the tripod
to provide a means for leveling the theodolite
none of the above

⇒ Subtense bar is an instrument used for
levelling
measurement of horizontal distances in plane areas
measurement of horizontal distances in undulated areas
measurement of angles

⇒ The direction of steepest slope on a contour, is.
along the contour
at an angle of 45Â° to the contour
at right angles to the contour
none of these.

⇒ In levelling operation.
when the instrument is being shifted, the staff must not be moved
when the staff is being carried forward, the instrument must remain stationary
both (a) and (b)
neither (a) nor (b).

⇒ An ideal transition curve is.
cubic parabola
cubic spiral
clothoid spiral
true spiral.

⇒ In centesimal system circumference is divided Into
400 parts
360 parts
180 parts
240 parts

⇒ The polar axis of earth is shorten than equatorial axis by
4295 metre
9542 metre
42.95 kilometre
None of these

⇒ The radius of curvature of the arc of the bubble tube is generally kept.
10 m
25 m
50 m
100 m

⇒ Pick up the correct statement from the following:
the theodolite in which telescope can be rotated in vertical plane is called a transmit
when the vertical circle is to the left of the telescope during observation, it is called to be in left face
when the vertical circle is to the right of the telescope during observation, it is called to be in right face
all the above.

⇒ Prismatic compass is considered more accurate than a surveyor's compass, because.
it is provided with a better magnetic needle
it is provided with a sliding glass in the object vane
its graduations are in whole circle bearings
it is provided with a prism to facilitate reading of its graduated circle

⇒ If the smallest division of a vernier is longer than the smallest division of its primary scale, the vernier is known as
Direct vernier
Double vernier
Simple vernier
Retrograde vernier

⇒ A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to.
cumulative, + 0.11 m
compensating, Â± 0.11 m
cumulative, - 0.11 m
none of these

⇒ If the staff is not held vertical at a level¬ling station, the reduced level calculated from the observation would be
true R.L.
more than true R.L.
less than true R.L.
none of the above

⇒ Accurate measurement of deflection angles with a transit not properly adjusted may be made by.
setting the vernier A at zero at back station and then plunging the telescope
setting the vernier A at zero at back station and turning the instrument to the forward station
taking two back sights one with the telescope normal and the other with telescope inverted
none of these.

⇒ Plotting of inaccessible points on a plane table, is done by.
intersection
traversing
radiation
none of these.

⇒ The variation in magnetic declination may be
Diurnal variation
Annual variation
Secular variation
Any of the above

⇒ Contour interval is
the vertical distance between two con-secutive contours
the horizontal distance between two consecutive contours
the vertical distance between two points on same contour
the horizontal distance between two points on same contour

⇒ For orientation of a plane table with three points A, B and C, Bessel's drill is.
Align b through a and draw a ray towards c, align a through b and draw a ray towards c, finally align c through the point of intersection of the previously drawn rays
Align c through a and draw a ray towards b, align a through c and draw a ray towards b, finally align b through the point of intersection of the previously drawn rays
Align c through b and draw a ray towards a, align b through c and draw a ray towards a, finally align a, through the point of intersection of the previously, drawn rays
In the first two steps any two of the points may be used and a ray drawn towards the third point, which is sighted through the point of intersection of previously drawn rays in the final step.

⇒ The ratio of the angles subtended at the eye, by the virtual image and the object, is known as telescope's.
resolving power
brightness
field of view
magnification.

⇒ In case of a direct vernier scale.
graduations increase in opposite direction in which graduations of the main scale increase
smallest division is longer than smallest division of the main scale
graduations increase in the same direction in which graduations of the main scale increase
none of these.

⇒ Pick up the incorrect statement from the following :
while measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length
an increase in temperature causes a tape to increase in length and the measured distance is too large
the straight distance between end points of a suspended tape is reduced by an amount called the sag correction
a 100 m tape of cross section 10 mm x 0.25 mm stretches about 10 mm under 5 kg pull.