Question is ⇒ A lag compensator is essentially a, Options are ⇒ (A) low pass filter, (B) high pass filter, (C) band pass filter, (D) either (a) or (b), (E) , Leave your comments or Download question paper.

Question is ⇒ A lag compensator is essentially a, Options are ⇒ (A) low pass filter, (B) high pass filter, (C) band pass filter, (D) either (a) or (b), (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A lag compensator is essentially a
A.	low pass filter [Correct Answer]
B.	high pass filter [Wrong Answer]
C.	band pass filter [Wrong Answer]
D.	either (a) or (b) [Wrong Answer]
View Answer 5 -2 Explanation:- Answer : A Discuss it below : Adil Zulfiqar Said on 2019-07-01 13:15:09 An ideal lag compensator always adds negative phase to system and it is a integrator and integrator is a low pass filter. An ideal lead compensator always add positive phase to a system and it is a derivator and derivator is a high pass filter. !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In a common Emitter BJT amplifier, the maximum usable supply voltage is limited by
avalanche breakdown of Base emitter junction
collector to Base Breakdown voltage with emitter open (βV_CBO)
collector Emitter Breakdown voltage with base open (βV_CBO)
zener breakdown voltage of the emitter base Junction

⇒ In the figure, the
emits light when both S₁ and S₂ are closed
emits light when both S₁ and S₂ are open
emits light when only S₁ and S₂ is closed
does not Emit light, irrespective of the switched positions

⇒ An 8 bit data is to be entered into a parallel in register. The number of clock pulses required is
8
4
2
1

⇒ For a 2 port network, the O/P short circuit current was measured with a 1 volt source at the I/P then value of the current gives
h₁₂
y₁₂
h₂₁
y₂₁

⇒ In 8085 microprocessor, if interrupt service requests have been received from all of the following interrupts, then which one will be serviced first?
RST 5.5
RST 6.5
RST 7.5
None

⇒ The inverse Fourier transform of δ(t) is
∪(t)
1
δ(t)
e^j2pt

⇒ Probability of error in DPSK is less than PSK
TRUE
FALSE
equal
depend upon noise

⇒ A unit step function is used to represent the closing a switch in a constant voltage system.
TRUE
FALSE

⇒ For the given figure C(s)/R(s<
K
0.5 K
2 K
0.25 K

⇒ A moving coil instrument has a resistance of 0.6 Ω and full scale deflection at 0.1 A. To convert it into an ammeter of 0-15 A range, the resistance of shunt should be
0.6 Ω
0.06 Ω
0.1 Ω
0.004 Ω

⇒ The first row of the window is called ' Title bar '.
TRUE
FALSE

⇒ In the circuit shown in the figure, the approximate voltage at the transist
base and emitter respectively are -8 V and -7.3 V
base and collector respectively are -8 V and -5 V
Collector and emitter respectively are -5 V and -7.3
base, emitter and collector respectively are -8 V, 7.3 V and -5 V

⇒
Match the following:
List I (Modes) List II (Characteristic)
A. Evanescent 1. Rectangular waveguide does not support
B. Dominant mode 2. No wave propagation
C. TM₁₀ and TM₀₁ 3. Lowest cut-off frequency

A-1, B-2, C-3
A-2, B-3, C-1
A-1, B-3, C-2
A-2, B-1, C-3

⇒ Digital circuits mostly use
Diodes
Bipolar transistors
Diodes and bipolar transistors
Bipolar transistors and FETs

⇒ Which of the following does not cause losses in optical fibre cables?
Stepped index operation
Impurities
Microbending
Attenuation in glass

⇒ Which of the following stages has no phase inversion of the signal?
Two CE stages
Three CE stages
CE and CC stages
CE stage and emitter follower

⇒ In the schematic representation of bipolar junction transistor, the direction of arrow shows the direction of flow of
holes
electrons
holes in pnp and electrons in npn
electrons in pnp and holes in npn

⇒ A ripple counter has 4 bits and uses flip flops with propagation delay time of 25 ns. The maximum possible time for change of state will be
25 ns
50 ns
75 ns
100 ns

⇒ A coil of resistance R and inductance L has a capacitor C in parallel with it. The source frequency is adjusted to a value equal to resonant frequency. Another capacitor C is added in parallel with the above circuit, the source current will
increase
decrease
remain the same
may increase or decrease

⇒ Two resistors R₁ = 36 Ω ± 5% and R₂ = 75 Ω ± 5% are connected in series. The total resistance is
111 ± 0 Ω
111 ± 2.778 Ω
111 ± 5.55 Ω
111 ± 7.23 Ω

⇒ The function (sin x)/x
has a period 2p, decays with increasing x and has zeros at np, n = ± 1, ± 2
has a period p
has a period p/2
has a period 2p, decays with increasing x, is an even function and has zeros at np, n = ± 1, ± 2

⇒ Which of the following is not an electromagnetic device?
Hall transducer
Transformer
Speedometer
Eddy current damping device

⇒ Slotted line can be used for measurement of high frequencies
TRUE
FALSE

⇒ If D is diameter of circular waveguide the cutoff wave-length for TE₁₁ mode is equal to
1.706 D
2.11 D
0.82 D
0.41 D

⇒ The log magnitude curve for a constant gain K is a
horizontal straight line
horizontal straight line of magnitude 20 log K decibels
an inclined line having slope K
an inclined line having slope -K

⇒ The five flags in 8085 are designated as
Z, CY, S, P and AC
D, Z, S, P, AC
Z, C, S, P, AC
Z, CY, S, D, AC

⇒ An op-amp uses
RC coupling
direct coupling
transformer coupling
either (b) or (c)

⇒
Assertion (A): A band elimination filter attenuates signals whose frequencies lie between the cutoff frequencies.
Reason (R): A band elimination circuit is very different from band pass circuit.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ In the saturation region of CE output characteristics of n-p-n transistor, V_CE is about
0.5 V
15 V
- 0.5 V
- 15 V

⇒ Which statement is true for an ac circuit?
Active power is always less than apparent power
Active power cannot be more than apparent power
Active power is always more than reactive power
Active power cannot be more than reactive power

	List I (Modes)		List II (Characteristic)
A.	Evanescent	1.	Rectangular waveguide does not support
B.	Dominant mode	2.	No wave propagation
C.	TM₁₀ and TM₀₁	3.	Lowest cut-off frequency

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math