Question is ⇒ Loading effect is primarily caused by instruments having, Options are ⇒ (A) high resistance, (B) high sensitivity, (C) low sensitivity, (D) high range, (E) , Leave your comments or Download question paper.

Question is ⇒ Loading effect is primarily caused by instruments having, Options are ⇒ (A) high resistance, (B) high sensitivity, (C) low sensitivity, (D) high range, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Loading effect is primarily caused by instruments having
A.	high resistance [Wrong Answer]
B.	high sensitivity [Wrong Answer]
C.	low sensitivity [Correct Answer]
D.	high range [Wrong Answer]
View Answer 5 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which one of the following is correct? Energy of a power signal is
finite
zero
infinite
between 1 and 2

⇒ 2's complement of a given 3 or more bit number of non-zero magnitude is the same as the original number if all bits except
MSB are zero
LSB are zero
MSB are 1
LSB are 1

⇒ Find 'X' in the circuit be
∏(0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 15)
0
Σ(14)
1

⇒ MOSFET can be used as a
current controlled capacitor
voltage controlled capacitor
current controlled inductor
voltage controlled inductor

⇒ If E_b, the energy per bit of a binary digital signal is 10^-6 watt sec. and the one sided power spectral density of the white noise N₀ = 10^-5 W/Hz, then the output SNR of the matched filter is
26 dB
10 dB
20 dB
13 dB

⇒ For a push pull circuit the most favoured biasing method is
self bias
emitter bias
diode bias
collector bias

⇒ What is the characteristic of a good control system?
Sensitive to parameter variation
Insensitive to input command
Neither sensitive to parameter variation nor sensitive to input commands
Insensitive to parameter variation but sensitive to input commands

⇒ If a signal g(t) has energy E, then the energy of the signal g(2t) is equal to ...
E/2
E/4
E
2E

⇒ In AM, if modulation index is more than 100%, then
bandwidth increases
the wave gets distorted
power of the wave increases
efficiency of transmission increases

⇒ One limitation of constant k filters is that Z₀ is not constant in the pass band.
TRUE
FALSE

⇒ Loss angle of a good quality cable is about
1°
30°
70°
90°

⇒ Due to which of the following reasons a lightning conductor on top of a building is made into a pointed spike?
Dust particles may not accumulate
Charge per unit area becomes very high for lightening to discharge
Rain drops may not collect
None of the above

⇒ A transistor amplifier has pole
s₁
s₁ + s₂ + s₃ + s₄
s₁ + s₄
s₄

⇒ Which of the following is a microwave source with a 'cross-field' structure?
Double cavity klystron
Reflex klystron
Magnetron
Travelling wave tube

⇒

Assertion (A): For high frequency lines inductive reactance is very high as compared to ac resistance.

Reason (R): Due to skin effect ac resistance of line is higher than dc resistance.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ What is the propagation constant for air filled wave guide with dimensions a = 1.59" and b = 0.795" at 4.95 GHz?
0.6698
0.7698
0.503
0.6598

⇒ For Bode plot of (1 + jωT) has
slope of 20 dB/decade and phase angle + tan^-1 (ωT)
slope of - 20 dB/decade and phase angle + tan^-1 (ωT)
slope of 20 dB/decade and phase angle - tan^-1 (ωT)
slope of - 40 dB/decade and phase angle - tan^-1(ωT)

⇒ Orbital disturbances of a geosynchronous satellite are caused by the
moon
sun
earth
all of the above

⇒ In Java 31% gives an answer
3
4
42798
42828

⇒

Match the following:

	List I		List II
A.	Ratio of maximum energy stored to energy dissipated per cycle	1.	Propagation constant
B.	TEM mode is loss less medium	2.	Cutoff frequency is zero
C.	Ratio of frequency in radian to phase velocity of EM wave	3.	Quality factor of cavity
D.	TEM is the mode of lowest cutoff frequency	4.	Cylindrical waveguide

A-3, B-2, C-4, D-1
A-2, B-3, C-1, D-4
A-3, B-2, C-1, D-4
A-2, B-3, C-4, D-1

⇒ A circuit has two branches 1 and 2 in parallel. If |Q₁| = 8 KVAR and |Q₂| = 6 KVAR, the magnitude of total kvar drawn form supply will be
14 KVAR
2 KVAR
zero
14 or 2 KVAR

⇒ In figure the phase
will be 90° at ω = 0 and 0° at ω = ∞
will be 0° at ω = 0 and 90° at ω = ∞
will be 45° at ω = 0 and 0° at ω = ∞
will be 45° at ω = 0 and 90° at ω = ∞

⇒ In the circuit of figure for sinusoidal input the waveform of the output will be as show
figure A
figure B
figure C
figure D

⇒ In a CE amplifier the output coupling capacitor is short circuited. The dc collector voltage
will increase
may increase or decrease
will remain the same
will decrease

⇒ In a minimum function
the degree of numerator and denominator are equal
the degree of numerator and denominator are unequal
the degree of numerator is one more than degree of denominator
the degree of numerator is one less than degree of denominator

⇒ If the amplitude of the voltage is kept constant, but its frequency is raised to 6 kHz, the new deviation will be for the modulation index is, if f_m = 500 Hz, Δf = 2.25
6 kHz
12 kHz
27 kHz
54 kHz

⇒ In a semi converter feeding a resistive load, the firing angle is a. Each thyristor conducts for
p radians
(p - a) radians
(p + a) radians
(p - 0.5 a) radians

⇒

Assertion (A): In C arithmetic operations are pemiissible on ints, floats and chars.

Reason (R): In C every arithmetic operator must be written explicitly.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ Which of the following correctly declares a pointer to an array of intergers in C?
int * P [20]
int * P
int (* P) [20]
int * (P [20])

⇒ A rare gas having N atoms/m³ is subjected to an electric field E. The electric dipole moment per unit volume is proportional to N and E.
TRUE
FALSE