Question is ⇒ A humming noise in the differential is often caused by improper tooth contact between the, Options are ⇒ (A) Drive pinion & ring gear, (B) Axle and side gear, (C) Pinion and side gears, (D) , (E) , Leave your comments or Download question paper.

Question is ⇒ A humming noise in the differential is often caused by improper tooth contact between the, Options are ⇒ (A) Drive pinion & ring gear, (B) Axle and side gear, (C) Pinion and side gears, (D) , (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	A humming noise in the differential is often caused by improper tooth contact between the
A.	Drive pinion & ring gear [Correct Answer]
B.	Axle and side gear [Wrong Answer]
C.	Pinion and side gears [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the atmospheric suspended system the brakes are applied when
Vacuum is applied to both sides of the diaphragm
Atmospheric pressure is applied to both sides of the diaphragm
Atmospheric pressure is applied to one side of the diaphragm

⇒ In the vacuum suspended system, the brakes are applied when
Atmospheric pressure is applied to one side of the diaphragm
Vacuum is applied to both sides of diaphragm
Atmospheric pressure is applied to both sides of the diaphragm

⇒ During suction stroke the pressure inside the cylinder is
Equal to atmospheric pressure
Above atmospheric pressure
Above or below atmospheric pressure
Below atmospheric pressure

⇒ During compression stroke the air is compressed according to
Isothermal process
Hyperbolic process
Adiabatic process
Constant pressure process

⇒ In a vacuum suspended unit, when the brakes are on, the piston or diaphragm has on both sides of it
Atmospheric pressure
Vacuum
Hydraulic pressure

⇒ The power train transmits power from the engine to the
Crank shaft
Rear wheels
Front wheels
Steering gear

⇒ Piston compression rings are manufactured by
Aluminium
Cast iron
Steel
Bronze

⇒ The synchronizing device used in the transmission uses
Cone braking surfaces
Flat braking surfaces
Synchronizing pins

⇒ To correct heavy heel contact on the ring gear teeth, move the
Drive pinion in
Ring gear towards pinion
Ring gear away from pinion and adjust backlash

⇒ The brake pipe in hydraulic brakes is made up of
PVC
Steel
Rubber
Copper

⇒ The fit of the piston to the cylinder is measured at the
Piston skirt
Piston head
Point of minimum diameter

⇒ On a straight road, the ring gear
Rotates at the same speed as wheels
Rotates faster than wheels
Rotates slower than wheels
Does not rotate

⇒ In the overdrive, there is an arrangement whereby it is possible to lock stationary the
Ring gear
Sun gear
Planet pinion cage

⇒ Differential mechanism at the axle is provided mainly to
Enable the vehicle go round corners
Equalize the division of torque between the two wheels c. To provide a reduction ratio
To turn the drive through a right angle

⇒ For diesel engines the nominal compression ratio is from
17 to 21:1
7.5 to 8.5:1
30 to 40:1
1 to 5:1

⇒ The metering rod is designed to vary the size of which jets
High speed jets
Accelerating jets
Float level jets
Idle jets

⇒ The power train includes the clutch, propeller shaft, differential and ................
Steering gear
Front axles
Chassis
Transmission

⇒ If the connecting rod longer, the side thrust of the piston is
Increased
Constant
Decreased

⇒ The crankcase scavenging the the crankcase or underside of the piston acts as
An air compressor
A blower
A ventilator
A breather

⇒ The heat is added in the cycle at
Constant pressure
Constant volume
Approximately constant pressure and constant volume

⇒ Changing position of an object against an opposing force is called
Power
Torque
Energy
Work

⇒ Axle shaft of the three-quarter floating axle is subjected to
Bending stress only
Torsional stress only
Bending and torsional stress
Torsional stress and stress due to axial force during cornering

⇒ The automobile chassis consists of the engine, frame, power train, wheels, steering and ..............
The doors
Luggage boot
Wind shield
Braking system

⇒ A double acting shock absorber usually has
Unequal pressure acting on either sides
Equal pressure on either side
Pressure acting only on one side

⇒ In the torque converter, oil leaving the turbine is changed into a helping direction by curved
Pump vanes
Stator vanes
Turbine vanes

⇒ The ring gear is adjusted in the differential by use of
Selective washers of proper thickness
Bearing adjuster
Adjusting screws

⇒ Brake efficiency is a term which denotes
Efficiency of the braking system as a whole
Efficiency of the braking linings
The deceleration as percentage of gravity
Efficiency of the operating linkage

⇒ The tree general types of friction bearings are
Journal, ball and roller
Journal, guide and thrust
Journal, shaft and thrust

⇒ Overdrive is provided in the transmission of a vehicle to
Reach higher road speeds
improved fuel consumption
achieve better acceleration
carry more load

⇒ The function of the relay valve in a compressed air brake system is to
Limit the maximum pressure reached in brake chambers
Relieve air pressure in brake chambers when it reaches a maximum value
Reduce the effort required at the brake pedal
Speed up the supply of air to brake chambers located at a distance from brake valve