Question is ⇒ mphr, Options are ⇒ (A) 100g, (B) 1000g, (C) 1g, (D) 10g, (E) , Leave your comments or Download question paper.

Question is ⇒ mphr, Options are ⇒ (A) 100g, (B) 1000g, (C) 1g, (D) 10g, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	mphr
A.	100g [Wrong Answer]
B.	1000g [Wrong Answer]
C.	1g [Correct Answer]
D.	10g [Wrong Answer]
View Answer 3 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The centre part of a typical universal joint is called the
Trunnion
Joint
Bearing
Spider

⇒ More often, the condition that draws attention to trouble in the differential is
Rough operation
Noise
Power loss

⇒ Almost all bearing used in automotive engines are
Guide bearings
Friction bearings
Antifriction bearings

⇒ In the fluid coupling, speed reduction means torque reduction. But in the torque converter, speed reduction means
Torque increase
Torque loss
Power increase

⇒ The ease with which a liquid changes to a vapour is called its
Vapourability
Boiling point
Viscosity
Volatility

⇒ The Ackermann steering layout
Makes for safer driving
Enables the driver to feel ahead position
Gives minimum tyre wear
Reduces load on the kingpins and stub axle

⇒ The type of rear axle in which the wheel end is supported by bearings inside the axle housing is
Semi floating axle
Three-quarter floating axle
Full-floating axle

⇒ With an increase in temperature the resistance of carbon is
Unchanged
Decreased
Increased

⇒ In the fluid coupling oil passes from the driving to the
Gear
Coupling
Vanes
Driven member

⇒ The maximum pressure of air at the end of compression in diesel engines is about
10 Kg/cm2
100 Kg/cm2
300 Kg/cm2
30 Kg/cm2

⇒ The type of braking system referred to as power brake, makes use of
Electromagnets
Compressed air
Vacuum

⇒ Braking is produced by the frictional effect between the brake drum and the
Wheel studs
Wheel rim
Brake shoes
Wheel cylinder pistons

⇒ The rotating effect of the connecting rod on the connecting rod bearing produces
Pressure load
Inertia load
Centrifugal load

⇒ The purpose of the fluid coupling is to act as a
Automatic gear changer
Flexible power transmitting coupling
Synchronizing device

⇒ The hydrodynamic torque converter
Gives a continuous variation of torque with increase of output speed
Enables to get the max. h.p continuously
Gives a speed variation without torque variation
Maintains a high efficiency throughout the operating speed range

⇒ Engine torque is highest at
High speed
Low speed
Intermediate speed

⇒ The conventional mechanical type fuel pump develops ............. pressure
0.15 Kg/cm2
1.0 Kg/cm2
0.5 Kg/cm2
0.3 Kg/cm2

⇒ In an operating engine, the hottest part of the piston is the
Head
Ring grooves
Skirt
Pin bosses

⇒ The distance between dual tyres of vehicles is to be correctly spaced to
Ensure proper distribution of load between dual wheels
Reduce over-steering effect
Reduce the slippage between tyre and road while taking a turn
Ensure effective braking

⇒ In the overdrive, there is an arrangement whereby it is possible to lock stationary the
Ring gear
Sun gear
Planet pinion cage

⇒ The function of the relay valve in a compressed air brake system is to
Limit the maximum pressure reached in brake chambers
Relieve air pressure in brake chambers when it reaches a maximum value
Reduce the effort required at the brake pedal
Speed up the supply of air to brake chambers located at a distance from brake valve

⇒ Weight can be attached to wheel rim to correct
Wheel alignment
Wheel run out
Wheel balance

⇒ In the vacuum suspended system, the brakes are applied when
Atmospheric pressure is applied to one side of the diaphragm
Vacuum is applied to both sides of diaphragm
Atmospheric pressure is applied to both sides of the diaphragm

⇒ Clutch slippage while clutch is engaged is particularly noticeable
When starting the engine
During acceleration
During idle
At low speed

⇒ The temperature of the piston will be more at
The piston walls
The crown of the piston
The skirt of the piston
The piston pin

⇒ The range of gear ratios in a vehicle depends on
The ratio of engine h.p to laden weight of vehicle
Max. engine torque / wt. of vehicle
Only on the laden weight of vehicle
The power to weight ratio of engine

⇒ When an automobile takes a tum to avoid the skidding and over turning
Each wheel will roll independently
Front two wheels will have a common centre during a turning
All the 4 wheels will roll on arcs having a common centre

⇒ In transmission reduction of speed is always used to obtain
Reduction of torque
Constant torque to drive the wheels
Increase of torque

⇒ The drive pinion in the over running clutch is moved into mesh for cranking action by
A shaft lever
Sleeve turning in pinion
Pinion inertia

⇒ In 'V' type engines the included angle between two banks of cylinders is
450
600
1300
900