Question is ⇒ If the differential noise is present only when the car is rounding a curve the trouble would be due to, Options are ⇒ (A) Heavy heel contact on gear teeth, (B) Heavy toe contact on gear teeth, (C) Binding in differential case, (D) , (E) , Leave your comments or Download question paper.

Question is ⇒ If the differential noise is present only when the car is rounding a curve the trouble would be due to, Options are ⇒ (A) Heavy heel contact on gear teeth, (B) Heavy toe contact on gear teeth, (C) Binding in differential case, (D) , (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If the differential noise is present only when the car is rounding a curve the trouble would be due to
A.	Heavy heel contact on gear teeth [Wrong Answer]
B.	Heavy toe contact on gear teeth [Wrong Answer]
C.	Binding in differential case [Correct Answer]
View Answer 4 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Two of the three connecting rod bearing loads that increase as engine speeds increase are
Centrifugal and inertia loads
Torsional and pressure loads
Pressure and inertia loads
Pressure and centrifugal loads

⇒ In a passenger car a typical arrangement of braking with drum brakes will be
Two leading shoes at front and leading & trailing at rear
All the wheels having leading and trailing shoes
All the wheels having two leading shoes
Front leading and trailing, rear two leading shoes

⇒ Parts of the clutch that should not be cleaned in solvent include the
Friction disc and throw out bearing
Friction disc cover
Throw out bearing and springs
Release levers and springs

⇒ BHP divided by IHP is
Thermal efficiency
Mechanical efficiency
Volumetric efficiency

⇒ In a vacuum type servo-assisted brake system, vacuum is available in ........ is made use of
Exhaust manifold
Combustion chamber
Water jackets
Inlet manifold

⇒ Toe out on turns
Is adjusted by shims
Is adjusted by changing the effective length of the tie rods
Cannot be adjusted

⇒ To prevent distortion on re-installation on the clutch cover attaching bolts should be tightened
One at a time
Evenly
Until springs begin to compress
Until springs are expanded

⇒ In the hydraulic braking system, the piston in the master cylinder is connected by mechanical linkage to the
Wheel cylinders
Brake shoes
Brake pedal
Wheel pedal

⇒ Clutch noises are usually most noticeable when the engine is
Being started
Decelerating
Idling
Accelerating

⇒ The sun gear in the planetary gear system meshes with the
Pinion cage
Ring gear
Clutch gear
Planet pinions

⇒ To correct heavy heel contact on the ring gear teeth, move the
Drive pinion in
Ring gear towards pinion
Ring gear away from pinion and adjust backlash

⇒ As compression ratio in an engine goes up, the octane requirements of the fuel
Goes down
Goes up
Stay about the same

⇒ Due to heat of combustion, with increase in temperature the molecules
Move slower
Vaporize
Move faster

⇒ The material used for the piston of modern passenger cars are
Brass pistons
Cast iron pistons
Aluminiun alloy pistons
Steel pistons

⇒ Piston compression rings are manufactured by
Aluminium
Cast iron
Steel
Bronze

⇒ The front end of the clutch shaft is supported in a pilot bearing in the
Throw out bearing
Friction disc
Crankshaft
Transmission

⇒ In general the design of the current regulator is such that its main actuating winding carries full
Generator voltage
Generator output
Field current
Battery voltage

⇒ The range of gear ratios in a vehicle depends on
The ratio of engine h.p to laden weight of vehicle
Max. engine torque / wt. of vehicle
Only on the laden weight of vehicle
The power to weight ratio of engine

⇒ Bleeding of brakes means
Filling the master cylinder with brake oil
Adjusting the brake shoe
Removing air between master cylinder and each wheel unit

⇒ The pump part that rotates and causes water circulation between the radiator and engine is called
Impeller
Fan
Bypass

⇒ The radiator tubes are manufactured by using
Cast iron tubes
Aluminum tubes
Brass tubes
Steel tubes

⇒ Gudgeon pins or piston pins are made by
Piston material itself
Cork
Cast iron
Hardened and ground steel

⇒ The conventional motor car has
Two forward speeds
Three forward speeds
Four forward speeds

⇒ The pipes used in diesel engines from pump to nozzle is made up of
PVC
Rubber
Steel
Copper

⇒ The part of the vehicle holds the passengers and the cargo to be transported is known as
Hull
Chassis
Cabin
Sedan

⇒ Which one of the following is not a trade name of tractor in India
Kirloskar
Escort
Standard
HMT

⇒ The type of braking system referred to as power brake, makes use of
Electromagnets
Compressed air
Vacuum

⇒ In the slip joint, slippage occurs between internally and externally mated
Couplings
joints
Splines

⇒ The most commonly used material for tyre tubes is
Butyl
Natural rubber
Butane

⇒ The fluid coupling has maximum efficiency when driving and driven members are turning at
High speed
Low speed
Different speed
About the same speed