Question is ⇒ If n is the number of sides then the total sum of exterior angles of a closed traverse should be, Options are ⇒ (A) n + 2, (B) 2n - 4, (C) 2n + 4, (D) 4n - 2, (E) , Leave your comments or Download question paper.

Question is ⇒ If n is the number of sides then the total sum of exterior angles of a closed traverse should be, Options are ⇒ (A) n + 2, (B) 2n - 4, (C) 2n + 4, (D) 4n - 2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If n is the number of sides then the total sum of exterior angles of a closed traverse should be
A.	n + 2 [Wrong Answer]
B.	2n - 4 [Wrong Answer]
C.	2n + 4 [Correct Answer]
D.	4n - 2 [Wrong Answer]
View Answer 29 -13 Explanation:- Answer : C Discuss it below : Sushma Said on 2016-12-21 23:09:47 (2n+4)x90 Hareesh Said on 2016-12-07 21:25:20 (2n+4)90 !! OOPS Login [Click here] is required to post your answer/result* Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Pick up the correct statement from the following :
it is difficult to eliminate an error completely at first trial
instability of the instrument makes it almost impossible to adjust it satisfactorily
adjustment screws must be left bearing firmly but should never be forced
all the above.

⇒ Check lines (or proof lines) in Chain Surveying, are essentially required.
to plot the chain lines
to plot the offsets
to indicate the accuracy of the survey work
to increase the out-turn

⇒ The method of finding out the difference in elevation between two points for eliminating the effect of curvature and refraction, is.
reciprocal levelling
precise levelling
differential levelling
flying levelling

⇒ The length of an engineer's chain should be
100 ft.
60 ft.
30m
20m

⇒ The cross hairs in the surveying telescope are placed
midway between eye piece and objec¬tive lens
much closer to the eye-piece than to the objective lens
much closer to the objective lens than to the eye piece
anywhere between eye-piece and objective lens

⇒ In direct method of contouring, the process of locating or identifying points lying on a contour is called
ranging
centring
horizontal control
vertical control

⇒ At the equator, the amount of dip is
0°
45°
60°
90°

⇒ In a perfect prismatic compass.
magnetic axis and geometric axis of the needle coincide
ends of the needle and pivot are in same vertical and horizontal planes
pivot is vertically over the centre of the graduated circle
all the above.

⇒ Pick up the correct statement from the following :
mistakes arise from inattention, inexperience or carelessness
systematic errors persist and have regular effects in the survey performances
accidental errors occur inspite of every precaution is taken
all the above.

⇒ Pick up the correct statement from the following :
The horizontal angle between magnetic meridian and true meridian at a place is called magnetic declination or variance of the compass
the imaginary lines which pass through points at which the magnetic declinations are equal at a given time are called isogonic lines
the isogonic lines through places at which the declination is zero are termed agonic lines
all the above.

⇒ Principle of surveying followed to prevent accumulation of errors is
To work from whole to the part
To work from part to whole
Both (A) and (B)
None of the above

⇒ If L is in kilometres, the curvature correction is.
58.2 L2 mm
64.8 L2 mm
74.8 L2 mm
78.4 L2 mm.

⇒ If the intercept on a vertical staff is ob-served as 0.75 m from a tacheometer, the horizontal distance between tacheometer and staff station is
7.5 m
25 m
50
75 m

⇒ Imaginary line passing through points having equal magnetic declination is termed as.
isogon
agonic line
isoclinic line
none of these.

⇒ One of the Lehmann's rules of plane tabling, is.
location of the instrument station is always distant from each of the three rays from the known points in proportion to their distances
when looking in the direction of each of the given points, the instrument station will be on the right side of one and left side of the other ray
when the instrument station is outside the circumscribing circle its location is always on the opposite side of the ray to the most distant point as the inter-section of the other two rays
none of these.

⇒ Pick up the correct statement from the following :
in the earth's magnetic field, a magnetic needle rests in magnetic meridian
the angle between the true meridian and the magnetic meridian is called magnetic variation
one end of the magnetic needle supported at its centre of gravity tends to dip down towards the. nearer magnetic pole of the earth
all the above.

⇒ The main plate of a transit is divided into 1080 equal divisions. 60 divisions of the vernier coincide exactly with 59 divisions of the main plate. The transit can read angles accurate upto.
5"
10"
15"
20"

⇒ Simpson's rule for calculating areas states that the area enclosed by a curvilinear figure divided into an even number of strips of equal width, is equal to.
half the width of a strip, multiplied by the sum of two extreme offsets, twice the sum of remaining odd offsets, and thrice the sum of the even offsets
one third the width of a strip, multiplied by the sum of two extreme offsets, twice the sum of remaining odd offsets and four times the sum of the even offsets
one third the width of a strip, multiplied by the sum of two extreme offsets, four times the sum of the remaining odd offsets, and twice the sum of the even offsets
one sixth the width of a strip, multiplied by the sum of the two extreme offsets, twice the sum of remaining odd offsets and four times the sum of the even offsets

⇒ An offset rod is provided at its top with
Hook
Flag
Distance measuring arrangement
None of these

⇒ Reduced bearing of a line is an angle between.
north line and given line measured clockwise
north line and given line measured anticlockwise
east or west and the given line
given line and the part of the meridian whether N end or S end, lying adjacent to it

⇒ The linen tape reinforced with brass or copper wires to prevent streching or twisting of fibres is called
Limen tape
Metallic tape
Invar tape
Cloth tape

⇒ Keeping the instrument height as 1.5 m, length of staff 4 m, the up gradient of the ground 1 in 10, the sight on the up slope must be less than
25 cm
20 m
45 m
10 m

⇒ The properties of autogenous curve for automobiles are given by.
true spiral
cubic parabola
Bernoulli's Lemniscate
clothoid spiral.

⇒ The radius of a simple circular curve is 300 m and length of its specified chord is 30 m. The degree of the curve is.
5.73Â°
5.37Â°
3.57Â°
3.75Â°.

⇒ The error in measured length due to sag of chain or tape is known as
Positive error
Negative error
Compensating error
Instrumental error

⇒ Which of the following methods of con-touring is most suitable for a hilly terrain ?
direct method
square method
cross-sections method
tacheometric method

⇒ Magnetic declination at a point
Does not change with time
Never remains constant
Varies with time
(B) and (C) above

⇒ If R is the radius of the main curve, θ the angle of deflection, S the shift and L the length of the transition curve, then, total tangent length of the curve, is.
(R - S) tan Î¸/2 - L/2
(R + S) tan Î¸/2 - L/2
(R + S) tan Î¸/2 + L/2
(R - S) tan Î¸/2 + L/2

⇒ Pick up the correct statement from the following :
the apparent error on reversal is twice the actual error
the correction may be made equal to half the observed discrepancy.
the good results may be obtained from a defective instrument by reversing and taking the mean of two erroneous results
all the above.

⇒ Traversing is generally done by
Chain
Compass or theodolite
Plane table
All the above are correct