Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | For the beam shown in the below figure, the shear force at A is equal to |

A. | wl/6 [Wrong Answer] |

B. | wl/3 [Correct Answer] |

C. | wl [Wrong Answer] |

D. | 2 wl/3 [Wrong Answer] |

View Answer
Explanation:-
Answer : BDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ In case of an over-reinforced beam, the depth of actual neutral axis is the same as that of the critical neutral axis.

True

False

Agree

Disagree

⇒ The capacity of a strained body for doing work on the removal of the straining force, is called

strain energy

resilience

proof resilience

impact energy

⇒ The stress necessary to initiate yielding is

considerably greater than that necessary to continue it

considerably lesser than that necessary to continue it

greater than that necessary to stop it

lesser than that necessary to stop it

⇒ The maximum shear stress is __________ the algebraic difference of maximum and minimum normal stresses.

equal to

one-fourth

one-half

twice

⇒ The deformation per unit length is called?

tensile stress

compressive stress

shear stress

strain

⇒ In a simply supported beam carrying a uniformly distributed load w per unit length, the point of contraflexure.

lies in the centre of the beam

lies at the ends of the beam

depends upon the length of beam

does not exist

⇒ Which of the following statement is correct?

The size of hole drilled in riveting plates is less than the actual size of rivet.

The centre to centre distance between two consecutive rivets in a row is called margin.

Rivets are generally specified by its shank diameter.

Tearing of plates can be avoided by taking the pitch of rivets equal to 1.5 times the diameter of rivet hole.

⇒ When there is a sudden increase or decrease in shear force diagram between any two points, it indicates that there is a

point load at the two points

no loading between the two points

uniformly distributed load between the two points

uniformly varying load between the two points

⇒ The value of Poisson's ratio for cast iron is

0.1 to 0.2

0.23 to 0.27

0.25 to 0.33

0.4 to 0.6

⇒ In a tensile test on mild steel specimen, the breaking stress as compared to ultimate tensile stress is

more

less

same

more/less depending on composition

⇒ The springs in brakes and clutches are used to?

to apply forces

to measure forces

to store strain energy

to absorb shocks

⇒ A rectangular beam of length

*l*supported at its two ends carries a central point load

*W*. The maximum deflection occurs.

at the ends

at l/3 from both ends

at the centre

none of these

⇒ The strain energy stored in a body, when suddenly loaded, is __________ the strain energy stored when same load is applied gradually.

equal to

one-half

twice

four times

⇒ A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear stress of 200 MPa. The minimum normal stress will be.

-100 MPa

250 MPa

300 MPa

400 MPa

⇒ A pressure vessel is said to be a thin shell when the ratio of wall thickness of the vessel to its diameter is __________ 1/10.

equal to

less than

greater than

none of these

⇒ For which material the Poisson's ratio is more than unity

steel

copper

aluminum

cast iron

⇒ A closely-coiled helical spring is cut into two halves. The stiffness of the resulting spring will be

same

double

half

one-fourth

⇒ When a cantilever beam is loaded at its free end, the maximum compressive stress shall develop at.

bottom fibre

top fibre

neutral axis

centre of gravity

⇒ If the tearing efficiency of a riveted joint is 50%, then ratio of rivet hole diameter to the pitch of rivets is?

0.20

0.30

0.50

0.60

⇒ When a beam is subjected to a bending moment, the strain in a layer is __________ the distance from the neutral axis.

equal to

directly proportional to

inversely proportional to

independent of

⇒ Resilience of a material is considered when it is subjected to

frequent heat treatment

fatigue

creep

shock loading

⇒ A beam supported on more than two supports is called

simply supported beam

fixed beam

overhanging beam

continuous beam

⇒ The ratio of linear stress to the linear strain is called

modulus of rigidity

modulus of elasticity

bulk modulus

Poisson's ratio

⇒ The energy absorbed in a body, when it is strained within the elastic limits, is known as

strain energy

resilience

proof resilience

modulus of resilience

⇒ A riveted joint may fail by.

tearing of the plate at an edge

tearing of the plate across a row of rivets

shearing of rivets

any one of these

⇒ A column of length (

*l*) with both ends fixed may be considered as equivalent to a column of length __________ with one end fixed and the other end free.

l/8

l/4

l/2

l

⇒ In the below figure, __________ represents glass.

curve A

curve B

curve C

curve D

⇒ In the below figure, curve

*C*represents soft brass.

True

False

Maximum

Minimum

⇒ The maximum strain energy that can be stored in a body is known as

impact energy

resilience

proof resilience

modulus of resilience

⇒ Rivets are generally specified by?

thickness of plates to be joined

overall length

shank diameter

diameter of head