Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | A column is said to be a short column, when. |

A. | its length is very small [Wrong Answer] |

B. | its cross-sectional area is small [Wrong Answer] |

C. | the ratio of its length to the least radhis of gyration is less than 80. [Correct Answer] |

D. | the ratio of its length to the least radius of gyration is more than 80. [Wrong Answer] |

View Answer
Explanation:-
Answer : CDiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The actual neutral axis of a reinforced cement concrete beam is based on the principle that the moment of areas of compression and tension zones at the neutral axis are equal.

Agree

Disagree

Both (a) and (b)

None of these

⇒ When a closely-coiled helical spring is subjected to an axial load, it is said to be under.

bending

shear

torsion

crushing

⇒ The ultimate tensile stress of mild steel compared to ultimate compressive stress is

same

more

less

more or less depending on other factors

⇒ In a thin cylindrical shell subjected to an internal pressure

*p*, the ratio of longitudinal stress to the hoop stress is.

1/2

3/4

1

1.5

⇒ A bar of copper and steel form a composite system, which is heated to a temperature of 40°C. The stress induced in the copper bar will be.

tensile

compressive

shear

zero

⇒ When a beam is subjected to bending moment, the stress at any point is __________ the distance of the point from the neutral axis.

equal to

directly proportional to

inversely proportional to

independent of

⇒ The total strain energy stored in a body is termed as

resilience

proof resilience

modulus of resilience

toughness

⇒ The impact strength of a material is an index of its

toughness

tensile strength

capability of being cold worked

hardness

⇒ A load which acts at a point on a beam is not called uniformly distributed load.

Agree

Disagree

True

False

⇒ Two shafts '

*A*' and '

*B*' are made of same material. The shaft '

*A*' is of diameter

*D*and shaft '

*B*' is of diameter

*D*/2. The strength of shaft '

*B*' is __________ as that of shaft '

*A*'

one-eighth

one-fourth

one-half

four times

⇒ The change in the unit volume of a material under tension with increase in its Poisson's ratio will ,

increase

decrease

remain same

increase initially and then decrease

⇒ The deformation of the bar per unit length in the direction of the force is known as.

linear strain

lateral strain

volumetric strain

shear strain

⇒ For the beam shown in the below figure, the shear force at

*A*is equal to

wl/6

wl/3

wl

2 wl/3

⇒ Lame's theory is associated with

thin cylindrical shells

thick cylindrical shells

direct and bending stresses

none of these

⇒ The bending moment diagram for a cantilever beam of length

*l*and carrying a gradually varying load from zero at the free end and

*w*per unit length at the fixed end is a parabolic curve.

Agree

Disagree

True

False

⇒ Rivets are made of following type of material

tough

hard

resilient

ductile

⇒ A riveted joint may fail by.

tearing of the plate at an edge

tearing of the plate across a row of rivets

shearing of rivets

any one of these

⇒ The shear force of a cantilever beam of length

*l*carrying a uniformly distributed load of

*w*per unit length is __________ at the free end.

zero

wl/4

wl/2

wl

⇒ A localised compressive stress at the area of contact between two members is known as.

tensile stress

bending stress

crushing stress

shear stress

⇒ The strain energy stored in a body due to suddenly applied load compared to when it is applied gradually is

same

twice

four times

eight times

⇒ The shear force diagram for a simply supported beam carrying a uniformly distributed load of

*w*per unit length, consists of.

one right angled triangle

two right angled triangles

one equilateral triangle

two equilateral triangles

⇒ Modulus of resilience is the proof resilience per unit volume of a material.

Correct

Incorrect

minimum

maximum

⇒ In the below figure, the stress corresponding to point

*D*is

yield point stress

breaking stress

ultimate stress

elastic limit

⇒ The torsional rigidity of a shaft is given by.

T/J

T/Î¸

T/r

T/G

⇒ When two plates are butt together and riveted with cover plates with two rows of rivets, the joi;it is known as

lap point

butt joint

single riveted single cover butt joint

double riveted double cover butt joint

⇒ In the below figure, the point

*C*represents

elastic limit

upper yield point

lower yield point

breaking point

⇒ In case of an over-reinforced beam, the depth of actual neutral axis is the same as that of the critical neutral axis.

True

False

Agree

Disagree

⇒ The shear force at the ends of a simply supported beam carrying a uniformly distributed load of

*w*per unit length is.

zero at its both ends

wl at one end and - wl at the other end

wl/2 at one end and - wl/2 at the other end

wl2/2 at one end and - wl2/2 at the other end

⇒ The moment of resistance of a balanced reinforced concrete beam is based on the stresses in

steel only

concrete only

steel and concrete both

none of these

⇒ A steel bar of 5 mm is heated from 15° C to 40° C and it is free to expand. The bar Will induce?

no stress

shear stress

tensile stress

compressive stress