Question is ⇒ Zoning is used with a dielectric antenna in order to, Options are ⇒ (A) permit pin-point focusing, (B) reduce the bulk of the lens, (C) increase the bandwidth of the lens, (D) correct the curvature of the wavefront from a horn that is too short, (E) , Leave your comments or Download question paper.

Question is ⇒ Zoning is used with a dielectric antenna in order to, Options are ⇒ (A) permit pin-point focusing, (B) reduce the bulk of the lens, (C) increase the bandwidth of the lens, (D) correct the curvature of the wavefront from a horn that is too short, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Zoning is used with a dielectric antenna in order to
A.	permit pin-point focusing [Correct Answer]
B.	reduce the bulk of the lens [Wrong Answer]
C.	increase the bandwidth of the lens [Wrong Answer]
D.	correct the curvature of the wavefront from a horn that is too short [Wrong Answer]
View Answer 3 -3 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following is/are not a property/properties power spectral density function Sx(ω)?
Sx(ω) is real function of ω
Sx(ω) is a even function of ω
Sx(ω) is non-positive function of ωSx(ω) ≤ 0 for all ω
All of the above

⇒ During fast forward operation of a tape recorder
all heads are withdrawn
all amplifiers are shut off
tape is not pressed against capstan
all of the above

⇒

Assertion (A): A band elimination filter attenuates signals whose frequencies lie between the cutoff frequencies.

Reason (R): A band elimination circuit is very different from band pass circuit.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ Consider the following

The first letter of a Java variable is lower case.
Each successive word in Java variable begins with a capital letter.
All other letters are lower case.
A Java variable can have a digit as first character.

Which of the above are correct?
All
1, 2, 3 only
1, 2, 4 only
2, 3, 4 only

⇒ The different access methods which permit many satellite users to operate in parallel through a single transponder without interfering with each other as
Frequency Division Multiple Access (FDMA)
Time Division Multiple Access (TDMA)
Code Division Multiple Access (CDMA)
All of the above

⇒ In a 4-ary FSK, the frequencies are separated by f_s. Then they are
in phase
in phase opposition
orthogonal
none of the above

⇒ The pre-emphasis in FM aids in providing extra noise immunity by
emphasizing only the higher frequency components
emphasizing the entire frequency band
emphasizing only the lower frequency band
cutting down the low frequency noise

⇒ An 8 bit DAC has a full scale output of 2 mA and full scale error of ± 0.5%. If input is 10000000 the range of outputs is
994 to 1014 μA
990 to 1020 μA
800 to 1200 μA
none of the above

⇒ Consider a loss less antenna with a directive gain of + 6 dB. If 1 mW of power is fed to it the total power radiated by the antenna will be
4 mW
1 mW
7 mW
1/4 mW

⇒ In air friction damping
the air pressure opposes the motion of piston when it is moving inwards
the air pressure opposes the motion of piston when it is moving outwards
the air pressure opposes the motion of piston both when it is moving inwards as well as outwards
the air pressure may oppose or aid the motion of piston depending on the design

⇒ Which of these triggering methods for series connected SCRs use LASCR in the gate circuit?
Resistance triggering
Simultaneous triggering
Sequential triggering
Optical triggering

⇒

Assertion (A): Different symbols are used for different gates

Reason (R): IEEE symbols are the same as traditional symbols for gates.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ The parallel RLC circuit shown in figure is in resonance
I_R < 1 mA
| I_R + I_L | > 1 mA
| I_R + I_L | < 1 mA
| I_L + I_C | > 1 mA

⇒ An excitation is applied to a system at t = T, and its response is zero for -∞ < t < T, such a system is
non-causal system
Stable system
causal system
unstable system

⇒ The frequency response of an ideal tuned amplifier should be as represented in figur
A
B
C
D

⇒ A 200 Hz sound wave is to be transmitted by a 1000 kHz radio wave using frequency modulation. The instantaneous frequency variation will be
100 times a second
200 times a second
400 times a second
1000 times a second

⇒ A capacitor used for power factor correction in single- phase circuit decreases
the power factor
the line current
both the line current and the power factor
the line current and increases power factor

⇒ Consider a multiplexer with X and Y as data inputs and Z as control input. Z = 0 selects input X and Z = 1 selects input Y. What are the connections required to realize the 2-variable Boolean function f = T + R, without using any additional hardware?
R to X, 1 to Y, T to Z
T to X, R to Y, T to Z
T to X, R to Y, 0 to Z
R to X, 0 to Y, T to Z

⇒ An n type semiconductor is illuminated by a steady flux of photons with energy greater than the band gap energy. The change in conductivity Δσ obeys which relati
Δσ = 0
Δσ = e(σ_n + σ_p) Δ_n
Δσ = e(μ_nΔ_n - μ_pΔ_p)
Δσ = e μ_nΔ_n

⇒ Transition capacitance is associated with __________ and depletion capacitance is associated with __________ diodes.
reverse bias and forward bias
forward bias and reverse bias
reverse bias and reverse bias
forward bias and forward bias

⇒ Which of the following statement is correct?
Decimal 9 is represented as 1011 in Excess-3 code
Decimal 9 is represented as 1001 is BCD code
Decimal 10 is represented as 1100 is Gray code
Decimal 10 is represented as 1001 in binary code

⇒ The voltage applied to an R-L circuit at t = 0 when switch is closed is 100 cos (100 t + 30°). The circuit resistance is 80 Ω and inductance is 0.6 H (in which initial current is zero). What is the maximum amplitude of current flowing through the circuit?
0.0416666666666667
0.0833333333333333
0.208333333333333
0.416666666666667

⇒ Examine the following statements

A small size hydraulic actuator can develop good torque.
It is easy to maintain a hydraulic system leak proof.
Both linear and rotatary hydraulic actuators are available.
Hydraulic power is more easily available than electric power.

Which of the above statements are correct?
all
1 and 2 only
1 and 3 only
2, 3 and 4 only

⇒ The Clapp oscillator shown in figure will operat
4.6 kHz
46 kHz
460 kHz
4600 kHz

⇒ In RLC circuits the state variables generally selected are
voltages across capacitors
currents through resistances and voltages across capacitors
currents through resistances and capacitances
currents through inductances and voltages across capacitances

⇒ An engineer designs an amplifier to have a voltage gain of 60, but when constructed it only had a gain of 50. What percentage of feedback will cause oscillations?
0.001
0.005
0.01
0.02

⇒ Which one of the following is true for EM wave propagation through rectangular waveguide of cross-section 2a x a
critical wavelength for TE₁₀ mode is the same as that for TE₀₂ mode
critical wavelength for TE₁₀ mode is one half of that for TE₁₀ mode
critical wavelength for TE₁₀ mode is the same as that for TM₁₀ mode
critical wavelength for TE₁₀ mode is double that for TE₀₁mode

⇒ For a periodic signal with finite number of discontinuities in each period, at isolated points of discontinuity the series converges to __________ .
difference value of signal on either side of discontinuity
highest value of signal on either side of discontinuity
average value of signal on either side of discontinuity
sum of value of signal on either side of discontinuity

⇒ Elements R, L, C are connected in parallel and excited by a dc current I. If i_R, i_L and i_C are the currents through R, L, C respectively then at t = 0
i_R > i_L > i_C
i_L > i_R > i_C
i_C = 0
i_C = I

⇒

Assertion (A): Even if TTL gates and CMOS gates used in a realization have the same power supply of + 5 V, suitable circuit is needed to interconnect them

Reason (R): V_OH, V_OL, V_IH and V_IL of a TTL gave are respectively 2.4, 0.4, 2 and 0.8 V respectively. If supply voltage is + 5 V. V_IL and V_IH for CMOS gate for the supply voltage of + 5 V are 1.5 V and 3.5 V respectively.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true