Question is ⇒ X(t) is a stationary process with the power spectral density Sx(f) > 0 for all f. The process is passed through a system shown be, Options are ⇒ (A) Sy(f) > 0 for all f, (B) Sy(f) = 0 for |f| > 1kHz, (C) Sy(f) = 0 for f = nf0, f0 = 2kHz, n any integer, (D) Sy(f) = 0 for f = (2n + 1)f0 = 1 kHz, n any integer, (E) , Leave your comments or Download question paper.

Question is ⇒ X(t) is a stationary process with the power spectral density Sx(f) > 0 for all f. The process is passed through a system shown be, Options are ⇒ (A) Sy(f) > 0 for all f, (B) Sy(f) = 0 for |f| > 1kHz, (C) Sy(f) = 0 for f = nf0, f0 = 2kHz, n any integer, (D) Sy(f) = 0 for f = (2n + 1)f0 = 1 kHz, n any integer, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	X(t) is a stationary process with the power spectral density S_x(f) > 0 for all f. The process is passed through a system shown be
A.	S_y(f) > 0 for all f [Wrong Answer]
B.	S_y(f) = 0 for \|f\| > 1kHz [Wrong Answer]
C.	S_y(f) = 0 for f = nf₀, f₀ = 2kHz, n any integer [Wrong Answer]
D.	S_y(f) = 0 for f = (2n + 1)f₀ = 1 kHz, n any integer [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The main difference between the broadside arrays and end fire arrays is that
individual elements are fed with same current in broadside arrays and of different magnitude in end fire arrays
in broadside arrays the elements are equidistant whereas in end fire array the distance between elements increases progressively
the total number of elements in broadside array is always one and a half times that of elements in end fire arrays
in broadside array the individual elements are fed in, out of phase by 180° whereas in end fire array individual elements are fed with currents of equal magnitude but their phases vary progressively along the line in such a way as to make the entire arrangement substantially unidirectional

⇒ In 8085, high level on INTR line can be recognised only if
TRAP and RST lines are high
TRAP and RST lines are not high
TRAP line is high but not RST line
RST line is high but not TRAP line

⇒ Which of the following methods can be used to measure power in a single phase circuit without using wattmeter?

One voltmeter, one ammeter
Two voltmeters, two ammeter
Three voltmeters
Three ammeters

1 and 2 only
2 and 4 only
1 and 3 only
3 and 4 only

⇒ K maps can be drawn
only for 2 variables
only for 3 variables
only for 4 variables
for any number of variables

⇒ What is the length of SP (Stack pointer) of 8085 μp?
6 bits
8 bits
12 bits
16 bits

⇒

Assertion (A): From the slope of the line in Figure, we can find permanent dipole moment of the molecules.

Reason (R): Total polarization of a polyatomic gas is given by P = N(a_e + a_i + μ²_p / 3kT
Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ Consider the following about 'arrays' in C

Which of the above are correct?
All
1 and 2 only
1 and 3 only
2 and 3 only

⇒ Which of the following statement is correct for two wattmeters method of power measurement in 3 phase circuit?
Power can be measured by this method only for star connected loads
When two wattmeters have equal readings power factor is 0.5.
When power factor is 1, one of the wattmeters readings is zero
When the two wattmeter read equal and opposite, p.f. is zero.

⇒ Leak type bias is used in plate modulated class C amplifier to
increase the bandwidth
prevent over modulation
prevent excessive grid current
prevent tuned circuit damping

⇒ Consider the following statements

Dissipative attenuator has a fixed value of attenuation.
Reflective attenuator has a fixed value of attenuation.
Both dissipative and reflective attenuators are available only with fixed attenuation.
Both dissipative and reflective attenuators are available with either fixed or variable attenuation.

Which of the above are correct?
1 only
1 and 2
1, 2 and 3
4 only

⇒ The dual of a node is
mesh
principal node
tree branch
link

⇒ A polyphase wattmeter basically consists of two wattmeters. The moving system of two wattmeters
are common
are separate
are generally common
are generally separate

⇒ The time base of a high frequency CRO whose screen diameter is 10 cm is set at 10 μ sec/cm. The lowest frequency which can be fully displayed on the screen is
more than 100 kHz
equal to 100 kHz
equal to 10 kHz
less than 10 kHz

⇒ Sometimes the rotating devices in a room having fluorescent lamps appear to be any station. This is due to
defect in the lamp
low voltage
high voltage
stroboscopic effect

⇒ If a signal g(t) has energy E, then the energy of the signal g(2t) is equal to ...
E/2
E/4
E
2E

⇒ In a circular waveguide the dominant mode is
TE₀₁
TE₁₁
TE₂₀
TE₂₁

⇒ In Jone chopper, the commutating element
is a capacitor
is a capacitor and an inductor
is a capacitor and an auto transformer
none of the above

⇒ To study electromagnetic radiations from astronomical objects, radio astronomers use
low frequencies
medium frequencies
microwaves
either (a) or (b)

⇒ Nichrome is commonly used for
lamp filaments
transformer winding
heater coils
battery connections

⇒ In the circuit, the value of the voltage sour
-22 V
-12 V
+12 V
-10 V

⇒ In the case of the circuit shown in the figure V_io = 10 mV dc maximum, the maximum possible output offset voltage V_oo caused by the input offset voltage V_io with respect to groun
60 mV dc
110 mV dc
130 mV dc
150 mV dc

⇒ An n channel depletion type MOSFET has
lightly doped p substrate and highly doped n source and drain
highly doped p substrate and highly doped n source and drain
highly doped p substrate and lightly doped n source and drain
lightly doped n substrate and highly doped n source and drain

⇒ In 8085, to disable the whole interrupt system (except TRAP)
the DI instruction may be used
the DO instruction may be used
the INTERRUPT instruction may be used
the El instruction may be used

⇒ The most widely used LC oscillator is
Hartley oscillator
Crystal oscillator
Colpitt's oscillator
Clapp's oscillator

⇒ During induction heating of metals which of the following is abnormally high?
Frequency
Voltage
Current
Power factor

⇒

Assertion (A): Magnetism can be explained by the theory of magnetic domains.

Reason (R): The existence of magnetic domains is evident from the Bitter powder patterns.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ The early effect in a BJT is caused by
fast turn on
fast turn off
large collector base reverse bias
large emitter base forward bias

⇒ The Hall constant in Si bar is given by 5 x 10³ cm³/ coulomb, the hole concentration in the bar is given by
10⁵/cm³
1.25 x 10¹⁵/cm³
1.5 x 10¹⁵/cm³
1.6 x 10¹⁵/cm³

⇒ The Boolean function A + BC is reduced form of
AB + BC
AB + ABC
(A + B) (A + C)
(A + C)B

⇒ An antenna having an effective temperature of 27°K is fed into a microwave amplifier that has an effective noise temperature of 30 K. Calculate the available noise power per unit bandwidth
30 K
57 K
27 K
3K, K is Boltzmann constant