Question is ⇒ Which statement is incorrect for the signal x(t) = 5 sin (2p x 103t) sin (2p x 106t)?, Options are ⇒ (A) Upper side band frequency is 1001000, (B) Carrier amplitude is 5, (C) Lower sideband frequency is 990000, (D) x(t) is DSB-SC, (E) , Leave your comments or Download question paper.

Question is ⇒ Which statement is incorrect for the signal x(t) = 5 sin (2p x 103t) sin (2p x 106t)?, Options are ⇒ (A) Upper side band frequency is 1001000, (B) Carrier amplitude is 5, (C) Lower sideband frequency is 990000, (D) x(t) is DSB-SC, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which statement is incorrect for the signal x(t) = 5 sin (2p x 10³t) sin (2p x 10⁶t)?
A.	Upper side band frequency is 1001000 [Wrong Answer]
B.	Carrier amplitude is 5 [Wrong Answer]
C.	Lower sideband frequency is 990000 [Correct Answer]
D.	x(t) is DSB-SC [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Electric breakdown strength of a material depends on its
composition
moisture content
thickness
all of the above

⇒

Assertion (A): Potentiometers can not be used as error detectors in position control systems.

Reason (R): The resolution of a potentiometer places an upper limit on its accuracy

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ When a ferromagnetic substance is magnetised, there are small changes in its dimensions. This phenomenon is called
hysteresis
magnetostriction
diamagnetism
bipolar relaxation

⇒ Class C operation finds application in
RF power amplifiers
frequency multipliers
both (a) and (b)
neither (a) nor (b)

⇒ Which of the following polynomials is not Hurwitz?
P₁ = s⁸ + 2s⁶ + 4s⁴
P₂ = s⁶ - 3s⁴ + 2s² + 1
P₃ = s⁴ + 3s³ + 3s² + 2s + 1
P₄ = s⁷ + 2s⁶ 2s⁴ + 4s³ + 8s² + 8s + 4

⇒ If interrupt service request have been received from all of the following interrupts, then which one will be serviced last?
RST 5.5
RST 6.5
RST 7.5
None of these

⇒ The coil of a moving coil meter has 100 turns, is 40 mm long and 30 mm wide. The control torque is 240 x 10^-6 N-m on full scale. If B = 1 Wb/m², range of meter is
1 mA
2 mA
3 mA
4 mA

⇒

Assertion (A): The phase angle plot in Bode diagram is not affected by change in system gain.

Reason (R): The variation in gain has no effect on phase margin of the system.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ What was the first commercial geostationary communication satellite?
INTELSAT 1
ECHO
INSAT-1A
SPUTNIK

⇒ The dual of a node is
mesh
principal node
tree branch
link

⇒ Frequencies in the UHF range propagate by means of
space wave
surface waves
sky waves
ground waves

⇒ The internal impedance of a source is 3 + j 4 Ω. It is desired to supply maximum power to a resistive load. The load resistance should be
3 Ω
4 Ω
7 Ω
5 Ω

⇒ In a mod-12 counter the input clock frequency is 10 kHz. The output frequency is
0.833 kHz
1.0 kHz
0.91 kHz
0.77 kHz

⇒ In an R-S latch, race condition occurs when
R is low and S is high
R and S are high
R and S are low
R is high and S is low

⇒ Permeance is analogue to
reluctance
conductance
capacitance
resistance

⇒ In a Karnaugh map for an expression having 'don't care terms' the don't cares can be treated as
0
1
1 or 0
none of the above

⇒ Square law modulators utilise
linear range of V-I characteristics of a diode
linear range of V-I characteristics of a triode
non-linear region of V-I dynamic characteristics of a diode
non-linear region of V-I dynamic characteristics of a triode

⇒ Push pull amplifier is
class B
class A
class C
Class A or Class C

⇒ A capacitance transducer has two plates each of area 5 mm². The coil gap is 2 mm. Displacement sensitivity due to change in gap length is
11.1 pF/cm
44.2 pF/cm
52.3 pF/cm
66.3 pF/cm

⇒ A signal x(t) = 100 cos (24p x 10³t) is ideally sampled with a sampling period of 50 μ sec and then passed through an ideal low pass filter with cut off frequency of 15 kHz Which of the following frequencies are present at the filter output?
12 kHz only
8 kHz only
12 kHz and 9 kHz
12 kHz and 8 kHz

⇒ For a semiconductor, the conductivity is a function of the products of the number of charge carriers and their mobilites. As result, if the temperature of a slab of intrinsic silicon increases, how does its conductivity vary?
Decreases
Increases
Remains unaffected
Increases or decreases depending upon the rise in temperature

⇒ In the circuit shown, the steady state is reached with S open S is closed at t = 0, the current I in the 1 Ω resistor connected is to be determined at t = 0⁺ is give
1
2
3
42828

⇒ An amplifier without feedback has a voltage gain of 50, input resistance of 1 kΩ and output resistance of 2.5 kΩ. The input resistance of the current shunt -ve feedback amplifier using the above amplifier with a feedback factor of 0.2 is
1/11 kΩ
1/5 kΩ
5 kW
11 kW

⇒ Zinc oxide is a non-linear resistance.
TRUE
FALSE

⇒ The circuit I in figur
1 mA
4 mA
8 mA
10 mA

⇒ Which one of the following is a trivalent material?
Antimony
Phosphorus
Arsenic
Boron

⇒ A series RLC circuit is supplied from a variable frequency source. The resonant frequency is ω₀. The voltage across L is maximum at a frequency
equal to ω₀
slightly less than ω₀
slightly more than ω₀
none of the above

⇒ A lag compensator
speeds up the transient response of the system
improves steady state behaviour of the system
improves steady state behaviour and speeds up the transient response of the system
improves steady state behaviour and preserves the transient response of the system

⇒ Two impedances are connected in series. Three voltmeters are connected, one across each impedance and one across combination. The readings of all the three are equal. The phase angle between voltages across the two impedances is
30°
60°
90°
120°

⇒ Shaft encoder is used to measure
angular position
linear position
linear velocity
linear acceleration