Question is ⇒ Which one of the following is not a useful quantity for comparing the noise performance of receivers?, Options are ⇒ (A) Noise figure, (B) Noise temperature, (C) Input noise voltage, (D) Equivalent noise resistance, (E) , Leave your comments or Download question paper.

Question is ⇒ Which one of the following is not a useful quantity for comparing the noise performance of receivers?, Options are ⇒ (A) Noise figure, (B) Noise temperature, (C) Input noise voltage, (D) Equivalent noise resistance, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which one of the following is not a useful quantity for comparing the noise performance of receivers?
A.	Noise figure [Wrong Answer]
B.	Noise temperature [Wrong Answer]
C.	Input noise voltage [Correct Answer]
D.	Equivalent noise resistance [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A microprocessor with a 16 bit address bus is used in a linear memory selection configuration. Address bus lines are directly uses as chip selects of memory chips with 4 memory chips the maximum addressable memory space is
64 k
16 k
8 k
4 k

⇒ R, L and C are in parallel. The circuit is switched on to a constant current source I at t = 0. At t = ∞ the current through inductance is I.
TRUE
FALSE

⇒ The maximum forward current in case of signal diode is in the range of
1 A to 10 A
0.1 A to 1 A
few milli amperes
few nano amperes

⇒ An SR flip flop can be built using NOR gates or NAND gates.
TRUE
FALSE

⇒ Which of the following is most likely to be found in an SSB transmitter?
Class A, RF output amplifier
Class B, RF amplifier
Tuned modulator
Class C, audio amplifier

⇒ Four memory chips of 16 x 4 size have their address buses connected together. This system will be of size
64 x 4
16 x 16
32 x 8
256 x 1

⇒

Assertion (A): In n-p-n transistor conduction is mainly due to electrons.

Reason (R): In n type materials electrons are majority carriers.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The input voltage for starting oscillations in an oscillator is caused by
negative feedback
positive feedback
noise voltage in resistors
a special generator

⇒ Which memory requires periodic recharging?
All ROMS
All RAMS
Static RAM
Dynamic RAM

⇒ Consider the following program for 8085 Adds decimal number 5 to contents of memory
Subtracts decimal number 5 from contents of memory
Subtracts decimal number 15 from contents of memory
Adds decimal number 15 to contents of memory

⇒ The hex number EB₁₆ represents binary number of
11101011
10010110
10101100
11101011

⇒ A + AB =
A
A
A + B
A + B

⇒ To measure a resistance by a dc potentiometer
it is necessary to standardise the potentiometer
it is not necessary to standardise the potentiometer
it is necessary to use a volt ratio box
none of the above

⇒

Assertion (A): L[af₁(t) + bf₂(t)] = aF₁(s) - bF₂(s)

Reason (R): Initial value theroem enables us to find the value of f(t) at t = 0 directly from F(s)

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In the given figure 15.6 shows a series, R - C circuit fed by a current source i(t). There is an initial voltage v₀. across the capacitor. The sy
is linear
is non linear
may be linear or non linear
is linear only if v₀ is zero

⇒ Most of the digital computers do not have floating-point hardware because
floating point hardware is costly
it is slower than software
it is not possible to perform floating point addition by hardware
of not specific reason

⇒ In a series RLC circuit excited by e = E_m sin ωt is seen that LC < 1/ω². Then
I lags E
I leads E
I leads E are in phase
voltage across L and C are equal

⇒ In C the range of real constants expressed in exponential form is
-2.3 e 37 to + 2.3 e 37
-3.4 e 38 to + 3.4 e 38
-3.4 e 37 to + 3.4 e 37
-2.3 e 38 to + 2.3 e 38

⇒ An electromechanical closed loop control system has the following characteristics equation :s³ + 6Ks² + (K + 2)s
K = 0.528
K = 2
K = 0
K = -2528

⇒ The fact that domains exhibits spontaneous magnetisation is
first hypothesis is of Curie
second hypothesis is of Weiss
Curie-Weiss law
Boltzmann's statistics

⇒ A choke coil of resistance R and inductance L is shunted by capacitor C. The dynamic resistance is
R/LC
C/RL
L/RC
1/RLC

⇒ In a line with finite attenuation
power transmission is least efficient when there are no standing waves on the line
power transmission is most efficient when there are no standing waves on line
Load power depends on phase constant
standing waves will always exist on the line

⇒ An RLC series circuit is fed form 100 V ac supply. Inductance is 1 H and Q = 7.5. At resonance, the voltage across inductance is
750 V
100 V
about 13.5 V
1500 V

⇒ The electrical requirement on wall thickness of rectangular wave guide is
wall thickness is more than skin depth
wall thickness is less than skin depth
wall thickness is equal to skin depth
either (b) or (c)

⇒ When a p-n-p transistor is operating in active region, the current in the n region is due to
only holes
only electrons
mainly holes
mainly electrons

⇒ The chip 8259 is a
programmable interrupt controller
programmable peripheral interface
I/O device
memory chip

⇒ The forbidden band in semiconductors is of the order of
6 eV
1 eV
10 eV
0.01 eV

⇒ A transmitted using AM has in modulated carrier output power of 10 KW and can be modulated to a maximum depth of 90% by a sinusoidal modulating voltage without causing overloading. Find the value to which an modulated carrier power can be increased without resulting in overloading if the maximum permitted modulating index is 40%
14 KW
12.96 KW
26.96 KW
2.96 KW

⇒ Which of the following is a valid real variable in FORTRAN 77?
KPR
LINE
JOB
RATE

⇒ In an n type semiconductor
number of free electrons and holes are equal
number of free electrons is much greater than the number of holes
number of free electrons may be equal or less than the number of holes
number of holes is greater than the number of free electrons