Question is ⇒ Which one of the following devices is not used as the controller in a stabilizer?, Options are ⇒ (A) DIAC, (B) TRIAC, (C) SCR, (D) Power transistor, (E) , Leave your comments or Download question paper.

Question is ⇒ Which one of the following devices is not used as the controller in a stabilizer?, Options are ⇒ (A) DIAC, (B) TRIAC, (C) SCR, (D) Power transistor, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which one of the following devices is not used as the controller in a stabilizer?
A.	DIAC [Correct Answer]
B.	TRIAC [Wrong Answer]
C.	SCR [Wrong Answer]
D.	Power transistor [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Is the interrupt-enable flag?
Low
High
Never
None

⇒ The rms value of wave in figur
about 95 V
about 80 V
about 50 V
about 25 V

⇒ The communicating capacitor reduces turn on time because
it acts as an open circuit
it allows maximum base circuit to flow
it aids in removing the excess carrier from the base region
none of these

⇒ To plot frequency spectrum we draw two graphs viz |F_n| versus frequency and φ_n versus frequency.
TRUE
FALSE

⇒ MCVF telegraphy causes
SSB techniques
pulse modulation
Out of bond signalling
FM

⇒ X and Y are two random variables and Z = X + Y . Letmz, m_z, m_x, m_y represent mean of Z, X and Y. Then
m_z = m_x + m_y
m_z ≤ m_x + m_y
m_z< m_x + m_y
m_z > m_x + m_y

⇒ A 0.5 μF capacitor is connected across a 10 V battery. After a long time, the circuit current and voltage across capacitor will be
0.5 A and 0 V
0 A and 10 V
20 A and 5 V
0.05 A and 5 V

⇒ In a multiphase chopper, all choppers operate together.
TRUE
FALSE

⇒ In the below figure the rms voltage across each half of secondary is 200 V. The peak inverse voltage across each of thyristor
200 V
2(200) V
2(400) V
800 V

⇒ It is desired to reduce the reflection at an air porcelain by use of 7/4 plate (for Porcelain μ = 40, and ε_r = 7). The thickness of the polystyrene plate required at 10 GHz will be
5.039 cm
50.39 cm
0.5039 cm
0.05039 cm

⇒ Which one of the following can be used for amplification of microwave energy?
TWT
Magnetron
Reflex klystron
Gunn diode

⇒ The h parameter equivalent to ac resistance r_e is
h_ib
h_fe
h_ob
h_rb

⇒ An AC circuit has two branches in parallel. The current in one branch is 5 A. Then the current source
must be less than 5 A
must be more than 5 A
may be equal or more or less than 5 A
0.208333333333333

⇒ The equivalent circuit shown in figure is
CE
CB
CC
None of the above

⇒ If the average power of radar transmitters is 2 kW and the peak power of the transmitter is 1000 kW, what will be the duty cycle?
0.002
0.02
0.001
0.01

⇒ In PCM, the information lies
in one or two properties of the pulse
in absence of pulse
in presence of pulse
in presence or absence of pulse

⇒ In a dual converter operated in circulating current mode, the circulating current flows
when load current is zero
when load current is non-zero
even when load current is zero
none of the above

⇒ Bandwidth of an antenna is related with where Q is quality factor
Q ∝ B
Q ∝ 1/B
Q ∝ B²
Q ∝ 1/B²

⇒ For the system of the given figure, the closed loop poles ar
0 and -4
-2 ± j6
2 ± j6
-3 ± j8

⇒ In a T flip-flop the output frequency is
same as input frequency
half of I/p frequency
double the input frequency
none

⇒ Which of these is also called 'hot carrier diode'?
PIN diode
LED
Photo diode
Schottky diode

⇒ The speeds used in recording audio programs in house hold recorders are
38 cm/s and 9.5 cm/s
38 cm/s and 19 cm/s
9.5 cm/s and 4.75 cm/s
38 cm/s and 4.75 cm/s

⇒ A load commutated chopper circuit has
one thyristor
two thyristors
four thyristors
six thyristors

⇒ For a junction FET in the pinch off region as the drain voltage is increased, the drain current
becomes zero
abruptly decreases
abruptly increases
remains constant

⇒ In a decimal digital computer, the number 127 is stored
1111111
0001 00100111
10001
11000111

⇒ Which one is true for writing array variable in Pascal?
The general form of an array variable is an integer or a real variable name followed by subscripts enclosed within square brackets. The subscripts are separated by commas
The general form of an array variable must be an integer name followed by subscripts enclosed within square brackets. The subscripts are separated by commas
The subscripts in array variable must be separated by dots
The subscripts must be enclosed within parenthesis

⇒ In case of probability of the message is 1 to 16 then the information will be
16 bits
8 bits
4 bits
2 bits

⇒ The internal impedance of a source is 3 + j 7 Ω. For maximum power transfer, load impedance should be
3 + j 7 Ω
3 - j 7 Ω
7 + j 3 Ω
7 - j 3 Ω

⇒ In an n channel JFET, the gate is
n type
p type
either n or p
partially n & partially p

⇒ The pole-zero configuration of the given figure can be
lag compensator
lead compensator
lead-lag compensator
series compensator