Question is ⇒ Which of the transistor models is most preferred for the analysis of a transistor circuit both at mid-band and at high frequencies?, Options are ⇒ (A) h-parameter model, (B) y-parameter model, (C) s-parameter model, (D) hybrid-p model, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the transistor models is most preferred for the analysis of a transistor circuit both at mid-band and at high frequencies?, Options are ⇒ (A) h-parameter model, (B) y-parameter model, (C) s-parameter model, (D) hybrid-p model, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the transistor models is most preferred for the analysis of a transistor circuit both at mid-band and at high frequencies?
A.	h-parameter model [Wrong Answer]
B.	y-parameter model [Wrong Answer]
C.	s-parameter model [Wrong Answer]
D.	hybrid-p model [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Consider the following statements regarding the properties of an R-L-C series circuit under resonance:

Current in the circuit is in phase with applied voltage
Voltage drop across capacitor C and inductance L are equal in magnitude.
Voltage across the capacitor is equal in magnitude to the applied voltage.
Current in the circuit is maximum.

Which of the above statements is/are correct?
1 only
1, 2 and 4
2 and 4
1, 3 and 4

⇒ When number of quantization levels are two; then the average transmission power in NRZ polar signaling is __________ that of NRZ unipolar signaling
42737
42739
42743
none of these

⇒ A (0.75 - j50) ohm load is connected to a coaxial transmission line of Z₀ = 75 ohms at a frequency of 10 GHz Which of the following will be the best method of matching?
Connecting an inductance at the end
Connecting a short circuited stub at the load
Connecting a capacitance at some distance from the load
Connecting a short circuited stub at some specified distance from the load

⇒ An SCR is triggered at 40° in the positive half cycle only. The average anode current is 50 A. If the firing angle is changed to 80°, the average anode current is likely to be
50 A
25 A
less than 50 A but more than 25 A
less than 25 A

⇒ The pinch-off voltage is the drain voltage on the shorted gate drain curve above which the drain current becomes
almost negligible
very high
almost constant
highly variable

⇒ The current flowing through a pure capacitor is called displacement current.
TRUE
FALSE

⇒ An RC impadence function has a pole at s = 0. The first element in the Foster form of synthesis
is R
may be R and C
is C
is R and C in parallel

⇒ Commercial Frequency deviation of FM is
70 kHz
75 kHz
80 kHz
65 kHz

⇒ In C the range of real constants expressed in exponential form is
-2.3 e 37 to + 2.3 e 37
-3.4 e 38 to + 3.4 e 38
-3.4 e 37 to + 3.4 e 37
-2.3 e 38 to + 2.3 e 38

⇒ Read the following statements about files in Pascal

A file is a data structure which consists of a sequence of components of the same type.
The number of components in a file is variable.
The components in a file can be accessed only sequentially starting from the beginning of the file.

Which of the above are correct?
All
1 and 2 only
2 and 3 only
1 and 3 only

⇒ To measure dielectric loss you would use
Anderson bridge
Kelvin bridge
Schering bridge
Maxwell's bridge

⇒ The current I_CBO flows in
base and emitter leads
base and collector leads
collector and emitter leads
collector, emitter and base leads

⇒ A 750 A circuit uses thyristor of current rating 175 A. If derating is 25%, the number of thyristors in parallel is
3
4
6
10

⇒

Assertion (A): In active region of CE output characteristics of BJT, collector current is nearly constant.

Reason (R): Base current in CE connection is very small.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The fabrication of microstrip line is done by
photo etching
printed circuit technique
oxidation
cladding

⇒ The phenomenon of overlap in converter operation due to
source resistance
source inductance
both source resistance and source inductance
high value of firing angle

⇒ In a commercially available good power supply the voltage regulation is about
0.01
0.05
0.1
0.2

⇒ In an n-type silicon crystal at room temperature, which of the following can have a concentration of 4 x 10¹⁹ cm^-3?
Silicon atoms
Holes
Dopant atoms
Valence electrons

⇒ When phase-lag compensation is used in a system, then gain cross over frequency, bandwidth and undamped frequency are respectively
Increased, Increased, Increased
Increased, Increased, Decreased
Increased, Decreased, Decreased
Decreased, Decreased, Decreased

⇒ Which of the following is not a valid variable name in C?
1 a
a 1 2
a b 123
a b c 123

⇒ In a JK flip flop toggle means
set Q = 1 and Q = 0
set Q = 0 and Q = 1
change the output to the opposite state
no change in output

⇒ NMOS devices have __________ switching speeds and __________ on-state resistance; as compared with PMOS devices.
slower, higher
faster, lower
faster, higher
slower, lower

⇒ Which of these devices can conduct in both directions?
SCR
SUS
SBS
UJT

⇒ Which chopper circuit operates in quadrants 1 and 4?
A
B
D
E

⇒ A message signal with bandwidth 10 kHz is lower sideband SSB modulated with carrier frequency f_c1 = 10⁶ Hz. The resulting signal is then passed though a narrow band frequency modulator with carrier frequency f_c2 = 10⁹ Hz. The bandwidth of the output would be
4 x 10⁴ Hz
2 x 10⁶ Hz
2 x 10⁹ Hz
2 x 10¹⁰ Hz

⇒ Recommended fanout for ECL is
5
10
15
25

⇒ A transmission line has primary constants R, L, G and C and secondary constant z₀ and γ = (a + Jβ). If the line is loss less, then
R = 0, G ≠ 0, and a = 0
R = 0, G = a, 0 and β = |r|
G = 0, a = β
R = 0, G = 0, a = 0, β = |r|

⇒ In graphical analysis of BJT amplifier the slope of ac line is more than that of dc load line.
TRUE
FALSE

⇒ The input to a coherent detector is DSB - SC signal plus noise. The noise at the detector output is
in phase component
quadrature component
zero
the envelope

⇒ In C the keywords are also called
special words
reserved words
class words
character words