Question is ⇒ Which of the following statements is correct, in case of a D.C. series motor ?, Options are ⇒ (A) It should be directly connected to the load, (B) It may run away if its field becomes open, (C) It is a constant speed motor, (D) It cannot be used where high starting torque is required, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following statements is correct, in case of a D.C. series motor ?, Options are ⇒ (A) It should be directly connected to the load, (B) It may run away if its field becomes open, (C) It is a constant speed motor, (D) It cannot be used where high starting torque is required, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following statements is correct, in case of a D.C. series motor ?
A.	It should be directly connected to the load [Correct Answer]
B.	It may run away if its field becomes open [Wrong Answer]
C.	It is a constant speed motor [Wrong Answer]
D.	It cannot be used where high starting torque is required [Wrong Answer]
View Answer 10 -2 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The armature torque of the D.C. shunt motor is proportional to
field flux only
armature current only
both (a) and (b)
none of the above

⇒ VVhat is the effect produced by the electric current in an electric motor ?
Heating effect only
Magnetic effect only
Heating as well as magnetic effect
Heating as well as chemical effect

⇒ The mechanical power developed by a D.C. motor is equal to
power input + losses
back e.m.f. X armature current
power output X losses
power output X efficiency

⇒ A series motor is started without load. The effect is that
the back e.m.f. decreases
the torque increases rapidly
the speed increases rapidly
the current drawn increases rapidly

⇒ During rheostatic braking the braking torque is proportional to
speed
(speed)²
(speed)^-1
(speed)^-2

⇒ Which of the following statement is incorrect ? If a starter is not used with large D.C. motor, it will draw a starting current which
will produce very low starting torque
will produce excessive line voltage drop
will damage the cOmmutator
is many times its full-load current

⇒ Four point starter in the D.C. motor is used
to decrease the field current
to increase the field current
not to effect the current passing through Hold on coil even if any change M the field current takes place
all of the above

⇒ Which of the following motor has high starting torque ?
Synchronous motor
A.C. series motor
D.C. series motor
Induction motor

⇒ Usually wide and sensitive speed control is desired in case of
centrifugal pumps
elevators
steel rolling mills
colliery winders

⇒ The hysteresis loss in a D.C. machine least depends on
Frequency of magnetic reversals
Maximum value of flux density
Volume and grade of iron
Rate of flow of ventilating air

⇒ In D.C. machines the residual magnetism is of the order of
2 to 3 per cent
10 to 15 per cent -
20 to 25 per cent
50 to 75 per cent

⇒ Which of the following motors is most suitable for signalling devices and many kinds of timers ?
D.C. shunt motor
D.C. series motor
Induction motor
Reluctance motor

⇒ Speed ,control by varying the armature circuit resistance, in a D.C. motor, provides a
constant torque drive
variable torque drive
constant power drive
variable power drive

⇒ Which loss in a D.C. generator does not vary with load as well as flux density ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ The function of a field regulator for compound motors is to
control the flux
limit the armature current
demagnetise the field partially
none of the above

⇒ In the D.C. motor the iron losses occur in
the field
the armature
the brushes
the commutator

⇒ The type of D.C. motor used for shears and punches is
shunt motor.
series motor
differential compound D.C. motor
cumulative compound D.C. motor

⇒ Which losses can be determined by performing the retardation test ?
Friction losses
Eddy current losses
Stray losses
Copper losses

⇒ Which D.C. motor is preferred for elevators ?
Shunt motor
Series motor
Differential compoun.d motor
Cumulative compound motor

⇒ Which D.C. motor will be preferred for cónstant speed line shafting ?
Cumulative compound motor
Differentially compound motor
Shunt motor
Series motor

⇒ A brake test on D.C. motors is usually restricted to
small horse power motors
variable speed motors
high speed motors
open frame type motors.

⇒ In a D.C. generator, the iron losses mainly take place in
yoke
commutator
armature conductors
armature rotor

⇒ Which D.C. motor has got maximum self loading property?
Series motor
Shunt motor
Cumulatively compounded motor
Differentially compotinded motor

⇒ If a D.C. shunt motor is working at full load and if shunt field circuit suddenly opens
this will make armature to take heavy current, possibly burning it
this will result in excessive speed, possibly destroying armature due to excessive centrifugal stresses
nothing will happen to motor
motor will come to stop

⇒ Which motor should be used for centrifugal pumps ?
Series motor
Shunt motor
Either of the above
None of the above

⇒ In case of D.C. shunt motors the speed is dependent on back e.m.f. only because
back e.m.f. is equal to armature drop
armature drop is negligible
flux is proportional to armature current
flux is practically constant in ac. shunt motors

⇒ Which of the following, in a D.C. motor, can sustain the maximum temperature rise ?
Commutator
Armature windings
Slip rings
Field windings

⇒ Why are the D.C. motors preferred for traction applications ?
Torque and speed are inversely proportional to armature current
Torque is proportional to armature current
Torque is proportional to square root of armature current
The speed is inversely proportional to the torque and the torque is proportional to square of armature current

⇒ If conditions for maximum power for a D.C. motor are established, the efficiency of the motor will be
less than 50%
60 to 70%
80 to 90%
1

⇒ Which of the following motor is preferred for operation in highly explosive atmosphere ?
Series motor
Shunt motor
Air motor
Battery operated motor