Question is ⇒ Which of the following statements is incorrect?, Options are ⇒ (A) Ideal voltage source is one whose internal resistance is zero, (B) Ideal voltage source is one whose internal conductance is zero, (C) Ideal voltage source is one whose generated voltage is equal to the available terminal voltage, (D) Ideal current source is one whose internal conductance is zero, (E) , Leave your comments or Download question paper.

Question is ⇒ Which of the following statements is incorrect?, Options are ⇒ (A) Ideal voltage source is one whose internal resistance is zero, (B) Ideal voltage source is one whose internal conductance is zero, (C) Ideal voltage source is one whose generated voltage is equal to the available terminal voltage, (D) Ideal current source is one whose internal conductance is zero, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Which of the following statements is incorrect?
A.	Ideal voltage source is one whose internal resistance is zero [Wrong Answer]
B.	Ideal voltage source is one whose internal conductance is zero [Correct Answer]
C.	Ideal voltage source is one whose generated voltage is equal to the available terminal voltage [Wrong Answer]
D.	Ideal current source is one whose internal conductance is zero [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The ability of a radio receiver to discriminate between different input signals and to accept only one definite signal is called its
sensitivity
attenuation
selectivity
modulation

⇒ A circuit is fed by two sources of the same frequency and values 100 ∠0° V and 20 ∠30°V. The current in a particular branch is 5 ∠19° A. If the magnitudes of the sources and changed to 200 ∠0° V and 40 ∠30° V, the current in that branch should be
5 ∠19° A
10 ∠19° A
10 ∠38° A
10 ∠9.5° A

⇒ For a NPN bipolar transistor, what is the main stream of current in the base region?
Drift of holes
Diffusion of holes
Drift of electrons
Diffusion of electrons

⇒ If the mantissa of a digital computer is 37 bit long then the accuracy of the digital computer will be of
37 decimal places
23 decimal places
11 decimal places
accuracy is independent of the length to mantissa

⇒ In microstrip line has dielectric material most commonly used is
silicon
rubber
plastic
bakelite

⇒ In CCD
a small charge is deposited for logical 1
a small charge is deposited for both logical 1 and 0
a small charge is deposited for logical 0 and large charge for logical 1
none of the above

⇒ If operator 'a' = 1 ∠120° then (1 + a²) =
3
3 ∠30°
3 ∠ - 30°
3 ∠60°

⇒ 24 telephone channels, each band limited to 3.4 kHz are to be time division multiplexed using PCM. If sampling frequency is 10 kHz and number of quantization levels is 128, the required bandwidth of PCM is
1.68 MHz
240 kHz
81.6 kHz
3.072 MHz

⇒ 1274₁₆ - 3A7₁₆ = __________ .
ACA₁₆
ACB₁₆
ECD₁₆
AAA₁₆

⇒ In 8085 microprocessor, what is the length of PC (program counter)?
6 bits
8 bit
12 bits
16 bits

⇒ Which of the following can provide two or more voice circuits with the same carrier?
SSB
Carrier reinsertion
Lincompex
Independent side band system

⇒ Transfer function of a linear system is 200 e^-j10ω The system is a
distortionless Attenuator
amplifier with Phase distortion
distortionless Amplifier
attenuator with Phase distortion

⇒ The chip 8254 is a 40 pin programmable interval timer. The number of its independent 16 bit counters is
2
3
4
5

⇒ The input impedance of CRO is about
zero
10 Ω
100 Ω
one mega ohm

⇒ In PAL system weighting of R - Y and B - Y signals is done to
prevent over modulation on saturated colours
prevent under modulation of saturated colours
allow over modulation of saturated colours
allow under modulation on saturated colours

⇒ A class C amplifier has input frequency of 200 kHz. If width of collector pulses is 0.1 μs, duty cycle is
0.01
0.02
0.1
0.2

⇒ A Hartley oscillator uses
a tapped capacitor
a tapped inductor
a tapped inductor for inductive feedback
none of the above

⇒ Consider the following time parameters

Domain growth time constant.
Transit time.
Dielectric relaxation time in positive mobility regime.

Which of the above are used in connection width transferred electron device?
1, 2, and 3
1 and 2 only
1 and 3 only
2 and 3 only

⇒ An XOR gate with 8 variable is as foll
255
127
128
256

⇒ A full wave rectifier circuit using centre tapped transformer, the input frequency 50 Hz. The frequency of output is
100 Hz
50 Hz
25 Hz
none of the above

⇒ When two 4 bit parallel adders are cascaded we get
4 bit parallel adder
8 bit parallel adder
16 bit parallel adder
none of the above

⇒ While using Maxwell bridge, the Q factor of a coil is obtained as
1/ωCR
ωCR
ωC/R
R/ωC

⇒ If transmitted power is 10 kW, the field strength at a distance d is 50 mV/m. If transmitted power is reduced to 2.5 kW, the field strength at the same point will be
25 mV/m
12.5 mV/m
6.25 mV/m
3.125 mV/m

⇒ A typical value of g_m for a FET is about 25 μs.
TRUE
FALSE

⇒ A transmitted using AM has in modulated carrier output power of 10 KW and can be modulated to a maximum depth of 90% by a sinusoidal modulating voltage without causing overloading. Find the value to which an modulated carrier power can be increased without resulting in overloading if the maximum permitted modulating index is 40%
14 KW
12.96 KW
26.96 KW
2.96 KW

⇒ A 12 bit ADC is operating with 1 μs clock period. Total conversion time is 14 μs. ADC is
flash type
counting type
integrating type
successive approximation type

⇒

Assertion (A): FET is a unipolar device.

Reason (R): BJT is bipolar device.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ A directional microphone gives an output of 0.5 mV whereas an omnidirectional one gives an output of 0.5 μV in the same position for the same sound pressure. The directivity of the directional microphone is
120 dB
90 dB
60 dB
30 dB

⇒ Two port network is said to be symmetrical if
Δ_h = 1
Z₁₁ = Z₂
A = Δ
all

⇒ The advantage of LVDT over inductive bridge type transducer is that
it gives high output for small changes in core position
it can be used over a temperature range of - 265°C to 600°C
it can measure displacement of moving object
the error due to stray magnetic field is less